ATMEGA16U2-MU Atmel, ATMEGA16U2-MU Datasheet - Page 242

• Manufacturer Part Number: ATMEGA16U2-MU
• Description: MCU AVR 16K FLASH USB 32-VQFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA16U2-MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Core: AVR8
• Processor Series: ATMEGA16x
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 16 MHz
• Data Ram Size: 1.25 KB
• Data Rom Size: 512 B
• Number Of Programmable I/os: 22
• Number Of Timers: 2
• Mounting Style: SMD/SMT
• Height: 0.95 mm
• Interface Type: SPI, UART
• Length: 5 mm
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Width: 5 mm
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32ATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Details

23.9
23.9.1
7799D–AVR–11/10
Register Description
SPMCSR – Store Program Memory Control and Status Register
The Store Program Memory Control and Status Register contains the control bits needed to con-
trol the Boot Loader operations.
• Bit 7 – SPMIE: SPM Interrupt Enable
When the SPMIE bit is written to one, and the I-bit in the Status Register is set (one), the SPM
ready interrupt will be enabled. The SPM ready Interrupt will be executed as long as the SPMEN
bit in the SPMCSR Register is cleared.
• Bit 6 – RWWSB: Read-While-Write Section Busy
When a Self-Programming (Page Erase or Page Write) operation to the RWW section is initi-
ated, the RWWSB will be set (one) by hardware. When the RWWSB bit is set, the RWW section
cannot be accessed. The RWWSB bit will be cleared if the RWWSRE bit is written to one after a
Self-Programming operation is completed. Alternatively the RWWSB bit will automatically be
cleared if a page load operation is initiated.
• Bit 5 – SIGRD: Signature Row Read
If this bit is written to one at the same time as SPMEN, the next LPM instruction within three
clock cycles will read a byte from the signature row into the destination register. see
the Signature Row from Software” on page 236
after SIGRD and SPMEN are set will have no effect. This operation is reserved for future use
and should not be used.
• Bit 4 – RWWSRE: Read-While-Write Section Read Enable
When programming (Page Erase or Page Write) to the RWW section, the RWW section is
blocked for reading (the RWWSB will be set by hardware). To re-enable the RWW section, the
user software must wait until the programming is completed (SPMEN will be cleared). Then, if
the RWWSRE bit is written to one at the same time as SPMEN, the next SPM instruction within
four clock cycles re-enables the RWW section. The RWW section cannot be re-enabled while
the Flash is busy with a Page Erase or a Page Write (SPMEN is set). If the RWWSRE bit is writ-
ten while the Flash is being loaded, the Flash load operation will abort and the data loaded will
be lost.
• Bit 3 – BLBSET: Boot Lock Bit Set
If this bit is written to one at the same time as SPMEN, the next SPM instruction within four clock
cycles sets Boot Lock bits, according to the data in R0. The data in R1 and the address in the Z-
pointer are ignored. The BLBSET bit will automatically be cleared upon completion of the Lock
bit set, or if no SPM instruction is executed within four clock cycles.
An (E)LPM instruction within three cycles after BLBSET and SPMEN are set in the SPMCSR
Register, will read either the Lock bits or the Fuse bits (depending on Z0 in the Z-pointer) into the
destination register. See
details.
Bit
0x37 (0x57)
Read/Write
Initial Value
SPMIE
R/W
7
0
RWWSB
R
6
0
“Reading the Fuse and Lock Bits from Software” on page 235
SIGRD
R/W
5
0
RWWSRE
R/W
4
0
for details. An SPM instruction within four cycles
ATmega8U2/16U2/32U2
BLBSET
R/W
3
0
PGWRT
R/W
2
0
PGERS
R/W
1
0
SPMEN
R/W
0
0
“Reading
SPMCSR
242
for