ATMEGA16U2-MU Atmel, ATMEGA16U2-MU Datasheet - Page 38

no-image

ATMEGA16U2-MU

Manufacturer Part Number
ATMEGA16U2-MU
Description
MCU AVR 16K FLASH USB 32-VQFN
Manufacturer
Atmel
Series
AVR® ATmegar
Datasheets

Specifications of ATMEGA16U2-MU

Core Processor
AVR
Core Size
8-Bit
Speed
16MHz
Connectivity
SPI, UART/USART, USB
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
22
Program Memory Size
16KB (8K x 16)
Program Memory Type
FLASH
Eeprom Size
512 x 8
Ram Size
512 x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
Core
AVR8
Processor Series
ATMEGA16x
Data Bus Width
8 bit
Maximum Clock Frequency
16 MHz
Data Ram Size
1.25 KB
Data Rom Size
512 B
Number Of Programmable I/os
22
Number Of Timers
2
Mounting Style
SMD/SMT
Height
0.95 mm
Interface Type
SPI, UART
Length
5 mm
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Supply Voltage (max)
5.5 V
Supply Voltage (min)
2.7 V
Width
5 mm
For Use With
ATSTK600 - DEV KIT FOR AVR/AVR32ATSTK500 - PROGRAMMER AVR STARTER KIT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Data Converters
-
Lead Free Status / Rohs Status
 Details

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATMEGA16U2-MU
Manufacturer:
RALINK
Quantity:
2 400
Company:
Part Number:
ATMEGA16U2-MU
Quantity:
250
8.11.2
8.11.3
8.11.4
7799D–AVR–11/10
CLKSEL1 – Clock Selection Register 1
CLKSTA – Clock Status Register
OSCCAL – Oscillator Calibration Register
lator is selected by the fuse bits configuration. The firmware has to check if the clock is correctly
started before selected it.
• Bit 7:4 – RCCKSEL[3:0]: CKSEL for RC oscillator
Clock configuration for the RC Oscillator. After a reset, this part of the register is loaded with the
0010b value that corresponds to the RC oscillator. Modifying this value by firmware before
switching to RC oscillator is prohibited because the RC clock will not start.
• Bit 3:0 – EXCKSEL[3:0]: CKSEL for External oscillator / Low Power Oscillator
Clock configuration for the External Oscillator / Low Power Oscillator. After a reset, if the Exter-
nal oscillator / Low Power Oscillator is selected by fuse bits, this part of the register is loaded
with the fuse configuration. Firmware can modify it to change the start-up time after the clock
switch.
• Bit 7:2 - Res: Reserved bits
These bits are reserved and will always read as zero.
• Bit 1 – RCON: RC Oscillator On
This bit is set by hardware to one if the RC Oscillator is running.
This bit is set by hardware to zero if the RC Oscillator is stoped.
• Bit 0 – EXTON: External Oscillator / Low Power Oscillator On
This bit is set by hardware to one if the External Oscillator / Low Power Oscillator is running.
This bit is set by hardware to zero if the External Oscillator / Low Power Oscillator is stoped.
• Bits 7:0 – CAL[7:0]: Oscillator Calibration Value
The Oscillator Calibration Register is used to trim the Calibrated Internal RC Oscillator to
remove process variations from the oscillator frequency. A pre-programmed calibration value is
automatically written to this register during chip reset, giving the Factory calibrated frequency as
specified in
Bit
(0xD1)
Read/Write
Initial Value
Bit
(0xD2)
Read/Write
Initial Value
Bit
(0x66)
Read/Write
Initial Value
Table 26-1 on page
RCCKSE
R/W
L3
7
0
CAL7
R/W
R
7
7
0
-
RCCKSE
R/W
L2
6
0
CAL6
R/W
R
6
6
0
-
RCCKSE
266. The application software can write this register to change
R/W
L1
CAL5
5
1
R/W
R
5
5
0
-
Device Specific Calibration Value
RCCKSE
R/W
CAL4
L0
0
R/W
4
R
4
4
0
-
EXCKSE
ATmega8U2/16U2/32U2
R/W
CAL3
R/W
L3
3
0
R
3
3
-
EXCKSE
See Bit Description
CAL2
R/W
R/W
L2
2
0
R
2
2
-
EXCKSE
RCON
CAL1
R/W
R/W
L1
R
1
1
1
0
EXCKSE
EXTON
CAL0
R/W
R/W
R
L0
0
0
0
0
OSCCAL
CLKSTA
CLKSEL1
38

Related parts for ATMEGA16U2-MU