PIC16F818-I/P Microchip Technology, PIC16F818-I/P Datasheet - Page 242

• Manufacturer Part Number: PIC16F818-I/P
• Description: IC MCU FLASH 1KX14 18-DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F818-I/P

• Program Memory Type: FLASH
• Program Memory Size: 1.75KB (1K x 14)
• Package / Case: 18-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: I2C/SPI/SSP
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 3
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163014
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 5-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: ACICE0202 - ADAPTER MPLABICE 18P 300 MILAC164010 - MODULE SKT PROMATEII DIP/SOIC
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PICmicro MID-RANGE MCU FAMILY
15.4.1.3
DS31015A-page 15-22
SDA
SCL
SSPIF
BF (SSPSTAT<0>)
CKP (SSPCON<4>)
S
Transmission
A7
1
Data in
sampled
A6
2
When the R/W bit of the incoming address byte is set and an address match occurs, the R/W bit
of the SSPSTAT register is set. The received address is loaded into the SSPBUF register. The
ACK pulse will be sent on the ninth bit, and the SCL pin is held low. The transmit data must be
loaded into the SSPBUF register, which also loads the SSPSR register. Then the SCL pin should
be enabled by setting the CKP bit (SSPCON<4>). The master must monitor the SCL pin prior to
asserting another clock pulse. The slave devices may be holding off the master by stretching the
clock. The eight data bits are shifted out on the falling edge of the SCL input. This ensures that
the SDA signal is valid during the SCL high time
An SSP interrupt is generated for each data transfer byte. The SSPIF flag bit must be cleared in
software, and the SSPSTAT register is used to determine the status of the byte transfer. The
SSPIF flag bit is set on the falling edge of the ninth clock pulse.
As a slave-transmitter, the ACK pulse from the master-receiver is latched on the rising edge of
the ninth SCL input pulse. If the SDA line was high (not ACK), then the data transfer is complete.
When the not ACK is latched by the slave, the slave logic is reset and the slave then monitors for
another occurrence of the START bit. If the SDA line was low (ACK), the transmit data must be
loaded into the SSPBUF register, which also loads the SSPSR register. Then the SCL pin should
be enabled by setting the CKP bit.
Figure 15-10:
A5
Receiving Address
3
A4
4
A3
5
A2
6
I
2
C Waveforms for Transmission (7-bit Address)
A1
7
R/W = 1
8
9
ACK
responds to SSPIF
SCL held low
while CPU
D7
1
SSPBUF is written in software
(Figure
D6
cleared in software
2
Set bit after writing to SSPBUF
(the SSPBUF must be written-to
before the CKP bit can be set)
D5
3
15-10).
D4
4
Transmitting Data
D3
5
1997 Microchip Technology Inc.
D2
6
From SSP interrupt
service routine
D1
7
D0
8
R/W = 0
ACK
9
P