PIC16F818-I/P Microchip Technology, PIC16F818-I/P Datasheet - Page 655

• Manufacturer Part Number: PIC16F818-I/P
• Description: IC MCU FLASH 1KX14 18-DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F818-I/P

• Program Memory Type: FLASH
• Program Memory Size: 1.75KB (1K x 14)
• Package / Case: 18-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: I2C/SPI/SSP
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 3
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163014
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 5-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: ACICE0202 - ADAPTER MPLABICE 18P 300 MILAC164010 - MODULE SKT PROMATEII DIP/SOIC
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

A.1
1997 Microchip Technology Inc.
Initiating and Terminating Data Transfer
During times of no data transfer (idle time), both the clock line (SCL) and the data line (SDA) are
pulled high through the external pull-up resistors. The START and STOP conditions determine
the start and stop of data transmission. The START condition is defined as a high to low transition
of the SDA when the SCL is high. The STOP condition is defined as a low to high transition of
the SDA when the SCL is high.
generates these conditions for starting and terminating data transfer. Due to the definition of the
START and STOP conditions, when data is being transmitted, the SDA line can only change state
when the SCL line is low.
Figure A-1:
Table A-1:
Transmitter
Receiver
Master
Slave
Multi-master
Arbitration
Synchronization
Term
Start and Stop Conditions
I
2
C Bus Terminology
The device that sends the data to the bus.
The device that receives the data from the bus.
The device which initiates the transfer, generates the clock and terminates
the transfer.
The device addressed by a master.
More than one master device in a system. These masters can attempt to
control the bus at the same time without corrupting the message.
Procedure that ensures that only one of the master devices will control the
bus. This ensure that the transfer data does not get corrupted.
Procedure where the clock signals of two or more devices are synchro-
nized.
SDA
SCL
Condition
Start
S
Figure A-1
Change
Allowed
of Data
shows the START and STOP conditions. The master
Description
Change
Allowed
of Data
Condition
Appendix A
Stop
P
DS31034A-page 34-3
34