PIC18F8410-E/PT Microchip Technology, PIC18F8410-E/PT Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
PIC18F8410-E/PT
Manufacturer Part Number
PIC18F8410-E/PT
Description
IC PIC MCU FLASH 16KX16 80TQFP
Manufacturer
Microchip Technology
Series
PIC® 18Fr
Datasheets
1.PIC18F6310-IPT.pdf
(412 pages)
2.PIC18F6310-IPT.pdf
(16 pages)
3.PIC18F6310-IPT.pdf
(4 pages)
4.PIC18F6310-IPT.pdf
(28 pages)
5.PIC18F6310-IPT.pdf
(6 pages)
6.PIC18F6310-IPT.pdf
(4 pages)
Specifications of PIC18F8410-E/PT
Core Processor
PIC
Core Size
8-Bit
Speed
40MHz
Connectivity
EBI/EMI, I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, HLVD, POR, PWM, WDT
Number Of I /o
70
Program Memory Size
16KB (8K x 16)
Program Memory Type
FLASH
Ram Size
768 x 8
Voltage - Supply (vcc/vdd)
4.2 V ~ 5.5 V
Data Converters
A/D 12x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
80-TFQFP
For Use With
XLT80PT3 - SOCKET TRAN ICE 80MQFP/TQFPAC164320 - MODULE SKT MPLAB PM3 80TQFPAC174011 - MODULE SKT PROMATEII 80TQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC18F8410-E/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
PIC18F6310/6410/8310/8410
17. Module: External Memory Bus (EMB)
18. Module: EUSART
19. Module: EUSART
20. Module: EUSART
DS80206F-page 8
When the EMB is enabled and configured for 8-bit
mode and EBDIS (MEMCON<7>) is clear, the BA0
pin continues to be active during table read and
table write operations to internal program memory
addresses. Under these conditions, BA0 should
be inactive.
Work around
Set the EBDIS bit when performing table
operations to internal program memory.
Date Codes that pertain to this issue:
All engineering and production devices.
The EUSART auto-baud feature may periodically
measure the incoming baud rate incorrectly. The
rate of incorrect baud rate measurements will
depend on the frequency of the incoming
synchronization byte and the system clock
frequency.
Work around
None.
Date Codes that pertain to this issue:
All engineering and production devices.
In Synchronous mode (SYNC = 1) with clock
polarity high (SCKP = 1), the EUSART transmits a
shorter than expected clock on the CKx pin for
bit 0.
Work around
None.
Date Codes that pertain to this issue:
All engineering and production devices.
In Synchronous mode, EUSART baud rates using
SPBRGx values of ‘0’ and ‘1’ may not function
correctly.
Work around
Use another baud rate configuration to generate
the desired baud rate.
Date Codes that pertain to this issue:
All engineering and production devices.
21. Module: MSSP
22. Module: MSSP
23. Module: MSSP
In an I
unaddressed slave may respond to bus activity
when data on the bus matches its address. The
first occurrence will set the BF bit. The second
occurrence will set the BF and SSPOV bits. In both
situations, the SSPIF bit is not set and an interrupt
will not occur. The device will vector to the Interrupt
Service Routine only if the interrupt is enabled and
an address match occurs.
Work around
The I
I
Date Codes that pertain to this issue:
All engineering and production devices.
In I
work correctly.
Work around
Use a BRG value greater than ‘0’ by setting
SSPADD ≥ 1.
Date Codes that pertain to this issue:
All engineering and production devices.
In I
ware to begin data reception and cleared by the
peripheral after a byte is received. After a byte is
received, the device may take up to 80 T
RCEN and 800 T
and MPLAB ICE emulators.
Work around
Single byte receptions are typically not affected,
since the delay between byte receptions is
typically long enough for the RCEN bit to clear. For
multiple byte receptions, the software must wait
until the bit is cleared by the peripheral before the
next byte can be received.
Date Codes that pertain to this issue:
All engineering and production devices.
2
C address match to maintain normal operation.
2
2
C Master mode, the BRG value of ‘0’ may not
C Master mode, the RCEN bit is set by soft-
2
C slave must clear the SSPOV bit after each
2
C™ system with multiple slave nodes, an
CY
© 2007 Microchip Technology Inc.
when using MPLAB
CY
®
to clear
ICD 2