DSPIC30F4013-20E/PT Microchip Technology, DSPIC30F4013-20E/PT Datasheet - Page 53

• Manufacturer Part Number: DSPIC30F4013-20E/PT
• Description: IC DSPIC MCU/DSP 48K 44TQFP
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F4013-20E/PT

• Program Memory Type: FLASH
• Program Memory Size: 48KB (16K x 24)
• Package / Case: 44-TQFP, 44-VQFP
• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 20 MIPS
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: AC'97, Brown-out Detect/Reset, I²S, POR, PWM, WDT
• Number Of I /o: 30
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 13x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Product: DSCs
• Data Bus Width: 16 bit
• Processor Series: DSPIC30F
• Core: dsPIC
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 30
• Data Ram Size: 2 KB
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE4000, DM240002, DM300018, DM330011
• Minimum Operating Temperature: - 40 C
• Package: 44TQFP
• Device Core: dsPIC
• Family Name: dsPIC30
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 3.3|5 V
• Interface Type: CAN/I2C/SPI/UART
• On-chip Adc: 13-chx12-bit
• Number Of Timers: 5
• Core Frequency: 20MHz
• Embedded Interface Type: CAN, I2C, SPI, UART
• No. Of I/o's: 30
• Flash Memory Size: 48KB
• Supply Voltage Range: 2.5V To 5.5V
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC30F006 - MODULE SKT FOR DSPIC30F 44TQFP
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: DSPIC30F401320EPT

11.13 Reading the Application ID Word
The application ID word is stored at address 0x8005BE
in executive code memory. To read this memory
location, you must use the SIX control code to move
this program memory location to the VISI register. The
REGOUT control code must then be used to clock the
contents of the VISI register out of the device. The
corresponding control and instruction codes that must
be serially transmitted to the device to perform this
operation are shown in
Once the programmer has clocked-out the application
ID word, it must be inspected. If the application ID has
the value 0xBB, the programming executive is resident
in memory and the device can be programmed using
the mechanism described in
Programming”. However, if the application ID has any
other value, the programming executive is not resident
in memory. It must be loaded to memory before the
device can be programmed. The procedure for loading
the programming executive to the memory is described
in
Executive to
TABLE 11-13: SERIAL INSTRUCTION EXECUTION FOR READING THE APPLICATION ID WORD
© 2010 Microchip Technology Inc.
Step 1: Exit the Reset vector.
0000
0000
0000
Step 2: Initialize TBLPAG and the read pointer (W0) for TBLRD instruction.
0000
0000
0000
0000
0000
0000
0000
0000
Step 3: Output the VISI register using the REGOUT command.
0001
0000
Command
Section 12.0 “Programming the Programming
(Binary)
Memory”.
040100
040100
000000
200800
880190
205BE0
207841
000000
BA0890
000000
000000
<VISI>
000000
(Hexadecimal)
Data
Table
11-13.
Section 5.0 “Device
GOTO 0x100
GOTO 0x100
NOP
MOV
MOV
MOV
MOV
NOP
TBLRDL [W0], [W1]
NOP
NOP
Clock out contents of the VISI register
NOP
#0x80, W0
W0, TBLPAG
#0x5BE, W0
VISI, W1
11.14 Exiting ICSP Mode
After confirming that the programming executive is
resident in memory, or loading the programming
executive, ICSP mode is exited by removing power to
the device or bringing MCLR to V
then take place by following the procedure outlined in
Section 5.0 “Device
Description
Programming”.
IL
. Programming can
DS70102K-page 53