AT89C5131A-PUTUM Atmel, AT89C5131A-PUTUM Datasheet - Page 135

• Manufacturer Part Number: AT89C5131A-PUTUM
• Description: IC 8051 MCU FLASH 32K USB 32QFN
• Manufacturer: Atmel
• Series: AT89C513xr

Specifications of AT89C5131A-PUTUM

• Core Processor: C52X2
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART, USB
• Peripherals: LED, POR, PWM, WDT
• Number Of I /o: 18
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 1.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Core: 8051
• Processor Series: AT89x
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 48 MHz
• Data Ram Size: 1.25 KB
• Number Of Programmable I/os: 34
• Number Of Timers: 16 bit
• Operating Supply Voltage: 2.7 V to 5.5 V
• Mounting Style: SMD/SMT
• Height: 0.95 mm
• Interface Type: 2-Wire, EUART, SPI, USB
• Length: 7 mm
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Width: 7 mm
• For Use With: AT89OCD-01 - USB EMULATOR FOR AT8XC51 MCUAT89STK-10 - KIT EVAL APPL MASS STORAGEAT89STK-05 - KIT STARTER FOR AT89C5131
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Details

Figure 21-12. Example of REMOTE WAKEUP Management
21.9
4337K–USB–04/08
Detach Simulation
SET_FEATURE: DEVICE_REMOTE_WAKEUP
Detection of a SUSPEND State
Upstream RESUME Sent
When the USB controller receives the SET_FEATURE request: DEVICE_REMOTE_WAKEUP,
the firmware will set to 1 the RMWUPE bit in the USBCON register to enable this functionality.
RMWUPE value will be 0 in the other cases.
If the device is in SUSPEND mode, the USB controller can send an upstream resume by clear-
ing first the SPINT bit in the USBINT register and by setting then to 1 the SDRMWUP bit in the
USBCON register. The USB controller sets to 1 the UPRSM bit in the USBCON register. All
clocks must be enabled first. The Remote Wake is sent only if the USB bus was in Suspend
state for at least 5 ms. When the upstream resume is completed, the UPRSM bit is reset to 0 by
hardware. The firmware will then clear the SDRMWUP bit.
In order to be re-enumerated by the Host, the AT89C5130A/31A-M has the possibility to simu-
late a DETACH - ATTACH of the USB bus.
The V
up as shown in
set to 1 in the USBCON register. Maintaining this output in high impedance for more than 3 µs
will simulate the disconnection of the device. When resetting the DETACH bit, an attach is then
simulated.
REF
UPRSM = 1
output voltage is between 3.0V and 3.6V. This output can be connected to the D+ pull-
Figure
21-13. This output can be put in high-impedance when the DETACH bit is
SPINT
UPRSM
Suspend Management
USB Controller Init
Clear SDRMWUP
Set SDMWUP
Set RMWUPE
Enable Clocks
Clear SPINT
AT89C5130A/31A-M
Need USB Resume
135