ATMEGA32U4-AU Atmel, ATMEGA32U4-AU Datasheet - Page 149

• Manufacturer Part Number: ATMEGA32U4-AU
• Description: MCU AVR 32K FLASH 16MHZ 44-TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA32U4-AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 26
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2.5K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Processor Series: ATMEGA32x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 2.5 KB
• Interface Type: SPI/TWI/USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 26
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12-ch x 10-bit
• Cpu Family: ATmega
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 16MHz
• Total Internal Ram Size: 2.5KB
• # I/os (max): 26
• Number Of Timers - General Purpose: 5
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 44
• Package Type: TQFP
• Controller Family/series: AVR MEGA
• No. Of I/o's: 26
• Eeprom Memory Size: 1KB
• Ram Memory Size: 2.5KB
• Cpu Speed: 16MHz
• Rohs Compliant: Yes
• For Use With: ATSTK524 - KIT STARTER ATMEGA32M1/MEGA32C1ATSTK600 - DEV KIT FOR AVR/AVR32ATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: ATMEGA32U4-16AU; ATMEGA32U4-16AU

15.7
15.8
15.8.1
7766F–AVR–11/10
Synchronous update
Modes of Operation
Normal Mode
To avoid unasynchronous and incoherent values in a cycle, if a synchronous update of one of
several values is necessary, all values can be updated at the same time at the end of the PWM
cycle by the Timer controller. The new set of values is calculated by software and the effective
update can be initiated by software.
Figure 15-11. Lock feature and Synchronous update
In normal operation, each write to a Compare register is effective at the end of the current cycle.
But some cases require that two or more Compare registers are updated synchronously, and
that may not be always possible, mostly at high speed PWM frequencies. That may result in
some PWM periods with incoherent values.
When using the Lock feature (TLOCK4=1), the values written to the Compare registers are not
effective and temporarily buffered. When releasing the TLOCK4 bit, the update is initiated and
the new whole set of values will be loaded at the end of the current PWM cycle.
See
The mode of operation, i.e., the behavior of the Timer/Counter and the Output Compare pins, is
defined by the combination of the Waveform Generation mode (bits PWM4x and WGM40) and
Compare Output mode (COM4x1:0) bits. The Compare Output mode bits do not affect the
counting sequence, while the Waveform Generation mode bits do. The COM4x1:0 bits control
whether the PWM output generated should be inverted, non-inverted or complementary. For
non-PWM modes the COM4x1:0 bits control whether the output should be set, cleared, or tog-
gled at a Compare Match.
The simplest mode of operation is the Normal mode (PWM4x = 0), the counter counts from
BOTTOM to TOP (defined as OCR4C) then restarts from BOTTOM. The OCR4C defines the
TOP value for the counter, hence also its resolution, and allows control of the Compare Match
output frequency. In toggle Compare Output Mode the Waveform Output (OCW4x) is toggled at
Compare Match between TCNT4 and OCR4x. In non-inverting Compare Output Mode the
Cycle with
Set i
Regulation Loop
Calculation
Section 15.12.5 ”TCCR4E – Timer/Counter4 Control Register E” on page
– Setting OCR4A = 0x85 (= b’10000101’) signifies that the true value of “Compare A”
register is 0x42 (b’01000010’) and that the Enhanced bit is set. That means that the
duty cycle obtained (51.95%) will be the intermediate value between duty cycles that
can be obtained by 0x42 and 0x43 Compare values (51.56%, 52.34%).
Cycle with
Set i
TLOCK4=1
Writing to Timer
Registers Set j
Cycle with
Set i
TLOCK4=0
Cycle with
Set i
Request for an
Update
Cycle with
Set j
ATmega16/32U4
169.
149