ATMEGA32U4-AU Atmel, ATMEGA32U4-AU Datasheet - Page 25

• Manufacturer Part Number: ATMEGA32U4-AU
• Description: MCU AVR 32K FLASH 16MHZ 44-TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA32U4-AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 26
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2.5K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Processor Series: ATMEGA32x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 2.5 KB
• Interface Type: SPI/TWI/USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 26
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12-ch x 10-bit
• Cpu Family: ATmega
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 16MHz
• Total Internal Ram Size: 2.5KB
• # I/os (max): 26
• Number Of Timers - General Purpose: 5
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 44
• Package Type: TQFP
• Controller Family/series: AVR MEGA
• No. Of I/o's: 26
• Eeprom Memory Size: 1KB
• Ram Memory Size: 2.5KB
• Cpu Speed: 16MHz
• Rohs Compliant: Yes
• For Use With: ATSTK524 - KIT STARTER ATMEGA32M1/MEGA32C1ATSTK600 - DEV KIT FOR AVR/AVR32ATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: ATMEGA32U4-16AU; ATMEGA32U4-16AU

5.3.5
7766F–AVR–11/10
Preventing EEPROM Corruption
Note:
During periods of low V
too low for the CPU and the EEPROM to operate properly. These issues are the same as for
board level systems using EEPROM, and the same design solutions should be applied.
An EEPROM data corruption can be caused by two situations when the voltage is too low. First,
a regular write sequence to the EEPROM requires a minimum voltage to operate correctly. Sec-
ondly, the CPU itself can execute instructions incorrectly, if the supply voltage is too low.
EEPROM data corruption can easily be avoided by following this design recommendation:
Keep the AVR RESET active (low) during periods of insufficient power supply voltage. This can
be done by enabling the internal Brown-out Detector (BOD). If the detection level of the internal
BOD does not match the needed detection level, an external low V
be used. If a reset occurs while a write operation is in progress, the write operation will be com-
pleted provided that the power supply voltage is sufficient.
Assembly Code Example
C Code Example
EEPROM_read:
unsigned char EEPROM_read(unsigned int uiAddress)
{
}
; Wait for completion of previous write
sbic EECR,EEPE
rjmp EEPROM_read
; Set up address (r18:r17) in address register
out EEARH, r18
out EEARL, r17
; Start eeprom read by writing EERE
sbi EECR,EERE
; Read data from Data Register
in
ret
/* Wait for completion of previous write */
while(EECR & (1<<EEPE))
/* Set up address register */
EEAR = uiAddress;
/* Start eeprom read by writing EERE */
EECR |= (1<<EERE);
/* Return data from Data Register */
return EEDR;
1. See “Code Examples” on page 8.
;
r16,EEDR
(1)
CC,
(1)
the EEPROM data can be corrupted because the supply voltage is
ATmega16/32U4
CC
reset Protection circuit can
25