DSPIC30F2020-30I/MM Microchip Technology, DSPIC30F2020-30I/MM Datasheet - Page 2
![IC DSPIC MCU/DSP 12K 28QFN](/photos/6/81/68120/150-28-qfn_sml.jpg)
DSPIC30F2020-30I/MM
Manufacturer Part Number
DSPIC30F2020-30I/MM
Description
IC DSPIC MCU/DSP 12K 28QFN
Manufacturer
Microchip Technology
Series
dsPIC™ 30Fr
Datasheets
1.AC164335.pdf
(286 pages)
2.DM300023.pdf
(22 pages)
3.DM300023.pdf
(18 pages)
4.DSPIC30F2011-20ISO.pdf
(66 pages)
5.DSPIC30F2011-20IP.pdf
(26 pages)
6.DSPIC30F1010-30ISO.pdf
(26 pages)
7.DSPIC30F1010-30ISO.pdf
(50 pages)
Specifications of DSPIC30F2020-30I/MM
Core Processor
dsPIC
Core Size
16-Bit
Speed
30 MIPs
Connectivity
I²C, IrDA, LIN, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
21
Program Memory Size
12KB (4K x 24)
Program Memory Type
FLASH
Ram Size
512 x 8
Voltage - Supply (vcc/vdd)
3 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
28-QFN
Core Frequency
15MHz
Core Supply Voltage
3.3V
Embedded Interface Type
I2C, SPI, UART
No. Of I/o's
21
Flash Memory Size
12KB
Supply Voltage Range
3V To 3.6V
Package
28QFN-S EP
Device Core
dsPIC
Family Name
dsPIC30
Maximum Speed
30 MHz
Operating Supply Voltage
3.3|5 V
Data Bus Width
16 Bit
Number Of Programmable I/os
21
Interface Type
I2C/SPI/UART
On-chip Adc
8-chx10-bit
Number Of Timers
3
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
DM300023 - KIT DEMO DSPICDEM SMPS BUCKAC164322 - MODULE SOCKET MPLAB PM3 28/44QFNDV164005 - KIT ICD2 SIMPLE SUIT W/USB CABLE
Eeprom Size
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DSPIC30F2020-30I/MMB32
Manufacturer:
Microchip Technology
Quantity:
135
2.1
In Enhanced ICSP mode, the dsPIC30F SMPS
requires a single programmable power supply for V
Refer to
Timing Requirements”
2.2
Table 2-2
programming. Refer to the appropriate device data
sheet for complete pin descriptions.
2.3
The program memory space extends from 0x0 to
0xFFFFFE. Code storage is located at the base of the
memory map and supports up to 12 Kbytes (4K
instruction words).
program memory size of each device.
TABLE 2-1:
TABLE 2-2:
DS70284C-page 2
MCLR
V
V
PGC
PGD
PGC1
PGD1
PGC2
PGD2
Legend: I = Input, O = Output, P = Power
Note 1:
dsPIC30F1010
dsPIC30F2020
dsPIC30F2023
DD
SS
dsPIC30F SMPS
Pin Name
and AV
and AV
Device
Pins Used During Programming
Program Memory Map
Section 13.0 “AC/DC Characteristics and
Hardware Requirements
lists the pins that are required for
All power supply and ground pins must be connected, including analog supplies (AV
(AV
SS
DD
(1)
SS
(1)
).
CODE MEMORY MAP AND
SIZE
PIN DESCRIPTIONS (PINS USED DURING PROGRAMMING)
Table 2-1
Pin Name
MCLR
PGC1
PGD1
PGC2
PGD2
PGC
PGD
for hardware parameters.
(Size in Instruction Words)
V
V
0x000000-0x000FFE (2K)
0x000000-0x001FFE (4K)
0x000000-0x001FFE (4K)
DD
SS
Code Memory Map
shows the location and
Pin Type
I/O
I/O
I/O
P
P
P
I
I
I
DD
Programming Enable
Power Supply
Ground
Primary Programming Pin Pair: Serial Clock
Primary Programming Pin Pair: Serial Data
Secondary Programming Pin Pair: Serial Clock
Secondary Programming Pin Pair: Serial Data
Tertiary Programming Pin Pair: Serial Clock
Tertiary Programming Pin Pair: Serial Data
.
During Programming
Locations 0x800000 through 0x8005BE are reserved
for executive code memory. This region stores either
the
executive. The programming executive is used for
device programming, while the debug executive is
used for in-circuit debugging. This region of memory
cannot be used to store user code.
Locations 0xF80000 through 0xF8000E are reserved
for the Configuration registers. The bits in these
registers may be set to select various device options,
and are described in
Programming”. The Configuration bits read out
normally, even after code protection is applied.
Locations 0xFF0000 and 0xFF0002 are reserved for
the Device ID registers. These bits can be used by the
programmer to identify which device type is being
programmed and are described in
“Device
after code protection is applied.
Figure 2-2
dsPIC30F SMPS devices.
2.4
The dsPIC30F SMPS family has no data EEPROM.
programming
Data EEPROM Memory
ID”. The device ID reads out normally, even
illustrates the memory map for the
Pin Description
Section 5.7 “Configuration Bits
executive
© 2010 Microchip Technology Inc.
DD
or
) and ground
the
Section 10.0
debugging