DSPIC30F2020-30I/MM Microchip Technology, DSPIC30F2020-30I/MM Datasheet - Page 186

• Manufacturer Part Number: DSPIC30F2020-30I/MM
• Description: IC DSPIC MCU/DSP 12K 28QFN
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F2020-30I/MM

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 30 MIPs
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 21
• Program Memory Size: 12KB (4K x 24)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-QFN
• Core Frequency: 15MHz
• Core Supply Voltage: 3.3V
• Embedded Interface Type: I2C, SPI, UART
• No. Of I/o's: 21
• Flash Memory Size: 12KB
• Supply Voltage Range: 3V To 3.6V
• Package: 28QFN-S EP
• Device Core: dsPIC
• Family Name: dsPIC30
• Maximum Speed: 30 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 16 Bit
• Number Of Programmable I/os: 21
• Interface Type: I2C/SPI/UART
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DM300023 - KIT DEMO DSPICDEM SMPS BUCKAC164322 - MODULE SOCKET MPLAB PM3 28/44QFNDV164005 - KIT ICD2 SIMPLE SUIT W/USB CABLE
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

dsPIC30F1010/202X
Example 16-1 shows a code sequence for using the
ADBASE register to implement ADC Input Pair Inter-
rupt Handling. When the ADBASE register is read, it
contains the sum of the base address of the jump table
and the encoded ADC channel pair number left shifted
by 2 bits.
EXAMPLE 16-1:
DS70178C-page 184
; Initialize and enable the ADC interrupt
; Code to Initialize the rest of the ADC registers
; ADC Interrupt Handler
__ADCInterrupt:
; Here's the Jump Table
; Note: It is important to clear the individual IRQ flags in the ADC AFTER the IRQ flags
in the interrupt controller. Failure to do so may cause interrupt requests to be lost
JMP_TBL:
MOV
MOV WO, ADBASE
BSET
BSET
BSET
BCLR
BCLR
BSET
...
...
...
PUSH.S
BCLR
MOV
GOTO
BCLR
BRA
BCLR
BRA
BCLR
BRA
BCLR
BRA
BCLR
BRA
#handle(JMP_TBL),W0
IPC2,#12
IPC2,#13
IPC2,#14
IFS0,#11
ADSTAT
IEC0,#11
IFSO,#11
ADBASE, W0
W0
ADSTAT,#0
ADC_PAIR0_PROC
ADSTAT,#1
ADC_PAIR1_PROC
ADSTAT,#2
ADC_PAIR2_PROC
ADSTAT,#3
ADC_PAIR3_PROC
ADSTAT,#4
ADC_PAIR4_PROC
ADC BASE REGISTER CODE
; Load the base address of the ISR Jump
; table in ADBASE.
; Set up the interrupt priority
; Clear any pending interrupts
; Clear the ADC pair interrupts as well
; Enable the interrupt
; Save WO-W3 and SR registers
; Clear the interrupt
; ADBASE contains the encoded jump address
; within JMP_TBL
; Clear the IRQ flag in the ADC
; Actual Pair 0 Conversion Interrupt Handler
; Clear the IRQ flag in the ADC
; Actual Pair 1 Conversion Interrupt Handler
; Clear the IRQ flag in the ADC
; Clear the IRQ flag in the ADC
; Actual Pair 3 Conversion Interrupt Handler
; Clear the IRQ flag in the ADC
; Actual Pair 4 Conversion Interrupt Handler
; Actual Pair 2 Conversion Interrupt Handler
Preliminary
For example, if ADBASE is initialized with a value of
0x0360, a channel pair 1 interrupt would cause an
ADBASE
0b00000100). A channel pair 3 interrupt would cause
an ADBASE read value of 0x036C (0x360 +
0b00001100).
read
value
© 2006 Microchip Technology Inc.
of
0x0364
(0x360
+