AT89C51ED2-RLTUM Atmel, AT89C51ED2-RLTUM Datasheet - Page 80

• Manufacturer Part Number: AT89C51ED2-RLTUM
• Description: IC 8051 MCU FLASH 64K 44VQFP
• Manufacturer: Atmel
• Series: 89Cr

Specifications of AT89C51ED2-RLTUM

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 60MHz
• Connectivity: SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 34
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Cpu Family: 89C
• Device Core: 8051
• Device Core Size: 8b
• Frequency (max): 40MHz
• Interface Type: SPI/UART
• Total Internal Ram Size: 2KB
• # I/os (max): 34
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 44
• Package Type: VQFP
• Processor Series: AT89x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Maximum Clock Frequency: 60 MHz
• Number Of Programmable I/os: 34
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Minimum Operating Temperature: - 40 C
• Package: 44VQFP
• Family Name: AT89
• Maximum Speed: 40 MHz
• For Use With: AT89OCD-01 - USB EMULATOR FOR AT8XC51 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Compliant

18. Power Management
18.1
18.2
18.2.1
18.2.2
80
Introduction
Idle Mode
AT89C51RD2/ED2
Entering Idle Mode
Exiting Idle Mode
Two power reduction modes are implemented in the AT89C51RD2/ED2. The Idle mode and the
Power-Down mode. These modes are detailed in the following sections. In addition to these
power reduction modes, the clocks of the core and peripherals can be dynamically divided by 2
using the X2 mode detailed in Section “Enhanced Features”, page 17.
Idle mode is a power reduction mode that reduces the power consumption. In this mode, pro-
gram execution halts. Idle mode freezes the clock to the CPU at known states while the
peripherals continue to be clocked. The CPU status before entering Idle mode is preserved, i.e.,
the program counter and program status word register retain their data for the duration of Idle
mode. The contents of the
Idle mode is detailed in Table 18-1.
To enter Idle mode, set the IDL bit in PCON register (see Table 18-2). The AT89C51RD2/ED2
enters Idle mode upon execution of the instruction that sets IDL bit. The instruction that sets IDL
bit is the last instruction executed.
Note:
There are two ways to exit Idle mode:
Note:
1. Generate an enabled interrupt.
2. Generate a reset.
– Hardware clears IDL bit in PCON register which restores the clock to the CPU.
– A logic high on the RST pin clears IDL bit in PCON register directly and
Execution resumes with the interrupt service routine. Upon completion of the
interrupt service routine, program execution resumes with the instruction
immediately following the instruction that activated Idle mode. The general purpose
flags (GF1 and GF0 in PCON register) may be used to indicate whether an interrupt
occurred during normal operation or during Idle mode. When Idle mode is exited by
an interrupt, the interrupt service routine may examine GF1 and GF0.
asynchronously. This restores the clock to the CPU. Program execution momentarily
resumes with the instruction immediately following the instruction that activated the
Idle mode and may continue for a number of clock cycles before the internal reset
algorithm takes control. Reset initializes the AT89C51RD2/ED2 and vectors the CPU
to address C:0000h.
If IDL bit and PD bit are set simultaneously, the AT89C51RD2/ED2 enters Power-Down mode.
Then it does not go in Idle mode when exiting Power-Down mode.
During the time that execution resumes, the internal RAM cannot be accessed; however, it is pos-
sible for the Port pins to be accessed. To avoid unexpected outputs at the Port pins, the instruction
immediately following the instruction that activated Idle mode should not write to a Port pin or to
the external RAM.
SFRs
and RAM are also retained. The status of the Port pins during
4235K–8051–05/08