STM32F103C6T7A STMicroelectronics, STM32F103C6T7A Datasheet - Page 12

• Manufacturer Part Number: STM32F103C6T7A
• Description: MCU ARM 32BIT 32KB FLASH 48LQFP
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F103C6T7A

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 72MHz
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART, USB
• Peripherals: DMA, Motor Control PWM, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 37
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 10K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 48-LQFP
• Featured Product: STM32 Cortex-M3 Companion Products
• Eeprom Size: -
• Cpu Family: STM32
• Device Core: ARM Cortex-M3
• Device Core Size: 32b
• Frequency (max): 72MHz
• Interface Type: CAN/I2C/SPI/USART
• Total Internal Ram Size: 10KB
• # I/os (max): 37
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 2V
• On-chip Adc: 2(10-chx12-bit)
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 105C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• For Use With: 497-10048 - BOARD EVAL ACCELEROMETER497-10030 - STARTER KIT FOR STM32KSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8511 - KIT STARTER FOR STM32 512K FLASH497-8505 - KIT STARTER FOR STM32F10XE MCU497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2MCBSTM32 - BOARD EVAL FOR STM STM32X SER497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Description
12/87
Figure 2.
1. When the HSI is used as a PLL clock input, the maximum system clock frequency that can be achieved is
2. For the USB function to be available, both HSE and PLL must be enabled, with USBCLK running at 48
3. To have an ADC conversion time of 1 µs, APB2 must be at 14 MHz, 28 MHz or 56 MHz.
64 MHz.
MHz.
OSC32_OUT
OSC32_IN
OSC_OUT
OSC_IN
MCO
Clock tree
4-16 MHz
32.768 kHz
Main
Clock Output
HSE OSC
LSE OSC
HSI RC
8 MHz
LSI RC
40 kHz
PLLSRC
MCO
x2, x3, x4
PLLMUL
HSI
..., x16
PLLXTPRE
PLL
/2
/128
LSE
/2
LSI
Doc ID 15060 Rev 5
RTCSEL[1:0]
/2
HSE
SYSCLK
PLLCLK
HSI
PLLCLK
RTCCLK
to Independent Watchdog (IWDG)
HSI
HSE
CSS
SW
SYSCLK
72 MHz
to RTC
max
IWDGCLK
Prescaler
/1, 2..512
AHB
Prescaler
/1, 1.5
USB
TIM1 timer
If (APB2 prescaler =1) x1
else
/1, 2, 4, 8, 16
/1, 2, 4, 8, 16
TIM2, TIM3
If (APB1 prescaler =1) x1
else
/8
Prescaler
Prescaler
72 MHz max
STM32F103x4, STM32F103x6
APB1
APB2
Prescaler
/2, 4, 6, 8
Clock
Enable (3 bits)
ADC
48 MHz
Legend:
HSE = high-speed external clock signal
HSI = high-speed internal clock signal
LSI = low-speed internal clock signal
LSE = low-speed external clock signal
72 MHz max
36 MHz max
ADCCLK
Peripheral Clock
Peripheral Clock
Enable (13 bits)
Enable (11 bits)
x2
USBCLK
to USB interface
x2
HCLK
to AHB bus, core,
memory and DMA
FCLK Cortex
free running clock
to Cortex System timer
Peripheral Clock
Enable (1 bit)
Peripheral Clock
Enable (3 bits)
TIM1CLK
TIMXCLK
PCLK1
PCLK2
to APB1
peripherals
to APB2
peripherals
to TIM2, TIM3
to ADC
to TIM1
ai15176