STM32F103C6T7A STMicroelectronics, STM32F103C6T7A Datasheet - Page 29

• Manufacturer Part Number: STM32F103C6T7A
• Description: MCU ARM 32BIT 32KB FLASH 48LQFP
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F103C6T7A

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 72MHz
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART, USB
• Peripherals: DMA, Motor Control PWM, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 37
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 10K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 48-LQFP
• Featured Product: STM32 Cortex-M3 Companion Products
• Eeprom Size: -
• Cpu Family: STM32
• Device Core: ARM Cortex-M3
• Device Core Size: 32b
• Frequency (max): 72MHz
• Interface Type: CAN/I2C/SPI/USART
• Total Internal Ram Size: 10KB
• # I/os (max): 37
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 2V
• On-chip Adc: 2(10-chx12-bit)
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 105C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• For Use With: 497-10048 - BOARD EVAL ACCELEROMETER497-10030 - STARTER KIT FOR STM32KSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8511 - KIT STARTER FOR STM32 512K FLASH497-8505 - KIT STARTER FOR STM32F10XE MCU497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2MCBSTM32 - BOARD EVAL FOR STM STM32X SER497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

STM32F103x4, STM32F103x6
5
5.1
5.1.1
5.1.2
5.1.3
5.1.4
5.1.5
Electrical characteristics
Parameter conditions
Unless otherwise specified, all voltages are referenced to V
Minimum and maximum values
Unless otherwise specified the minimum and maximum values are guaranteed in the worst
conditions of ambient temperature, supply voltage and frequencies by tests in production on
100% of the devices with an ambient temperature at T
the selected temperature range).
Data based on characterization results, design simulation and/or technology characteristics
are indicated in the table footnotes and are not tested in production. Based on
characterization, the minimum and maximum values refer to sample tests and represent the
mean value plus or minus three times the standard deviation (mean±3Σ).
Typical values
Unless otherwise specified, typical data are based on T
2 V ≤ V
tested.
Typical ADC accuracy values are determined by characterization of a batch of samples from
a standard diffusion lot over the full temperature range, where 95% of the devices have an
error less than or equal to the value indicated (mean±2Σ)
Typical curves
Unless otherwise specified, all typical curves are given only as design guidelines and are
not tested.
Loading capacitor
The loading conditions used for pin parameter measurement are shown in
Pin input voltage
The input voltage measurement on a pin of the device is described in
DD
≤ 3.6 V voltage range). They are given only as design guidelines and are not
Doc ID 15060 Rev 5
A
A
= 25 °C and T
.
= 25 °C, V
SS
.
Electrical characteristics
DD
A
Figure
= 3.3 V (for the
= T
Figure
A
max (given by
10.
9.
29/87