STM32F103C6T7A STMicroelectronics, STM32F103C6T7A Datasheet - Page 70

• Manufacturer Part Number: STM32F103C6T7A
• Description: MCU ARM 32BIT 32KB FLASH 48LQFP
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F103C6T7A

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 72MHz
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART, USB
• Peripherals: DMA, Motor Control PWM, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 37
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 10K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 48-LQFP
• Featured Product: STM32 Cortex-M3 Companion Products
• Eeprom Size: -
• Cpu Family: STM32
• Device Core: ARM Cortex-M3
• Device Core Size: 32b
• Frequency (max): 72MHz
• Interface Type: CAN/I2C/SPI/USART
• Total Internal Ram Size: 10KB
• # I/os (max): 37
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 2V
• On-chip Adc: 2(10-chx12-bit)
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 105C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• For Use With: 497-10048 - BOARD EVAL ACCELEROMETER497-10030 - STARTER KIT FOR STM32KSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8511 - KIT STARTER FOR STM32 512K FLASH497-8505 - KIT STARTER FOR STM32F10XE MCU497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2MCBSTM32 - BOARD EVAL FOR STM STM32X SER497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Electrical characteristics
70/87
Equation 1: R
The formula above
error below 1/4 of LSB. Here N = 12 (from 12-bit resolution).
Table 47.
1. Based on characterization, not tested in production.
Table 48.
1. ADC DC accuracy values are measured after internal calibration.
2. ADC Accuracy vs. Negative Injection Current: Injecting negative current on any of the standard (non-
3. Based on characterization, not tested in production.
1.5
7.5
13.5
28.5
41.5
55.5
71.5
239.5
Symbol
R
robust) analog input pins should be avoided as this significantly reduces the accuracy of the conversion
being performed on another analog input. It is recommended to add a Schottky diode (pin to ground) to
standard analog pins which may potentially inject negative current.
Any positive injection current within the limits specified for I
affect the ADC accuracy.
EO
EG
ED
ET
EL
AIN
<
------------------------------------------------------------- - R
f
T
ADC
Total unadjusted error
Offset error
Gain error
Differential linearity error
Integral linearity error
s
R
(cycles)
ADC accuracy - limited test conditions
×
AIN
AIN
C
(Equation
ADC
Parameter
max for f
max formula:
T
S
×
ln
(
1) is used to determine the maximum external impedance allowed for an
2
ADC
N
+
Doc ID 15060 Rev 5
0.11
0.54
0.96
2.04
2.96
3.96
5.11
17.1
2
)
= 14 MHz
–
f
f
V
T
Measurements made after
ADC calibration
ADC
PCLK2
ADC
A
DDA
= 25 °C
= 14 MHz, R
(1)
= 3 V to 3.6 V
t
S
= 56 MHz,
Test conditions
(µs)
INJ(PIN)
AIN
(1) (2)
and Σ I
< 10 kΩ,
STM32F103x4, STM32F103x6
INJ(PIN)
0.4
5.9
11.4
25.2
37.2
50
NA
NA
in
±1.3
±0.5
±0.7
±0.8
Typ
±1
Section 5.3.12
R
AIN
max (kΩ)
Max
±1.5
±1.5
±1.5
±1
±2
(3)
does not
Unit
LSB