STM32F103ZET7 STMicroelectronics, STM32F103ZET7 Datasheet - Page 57

• Manufacturer Part Number: STM32F103ZET7
• Description: MCU ARM 32BIT 512K FLASH 144LQFP
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F103ZET7

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 72MHz
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART, USB
• Peripherals: DMA, Motor Control PWM, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 112
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 21x12b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 144-LQFP
• Processor Series: STM32F103x
• Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Data Ram Size: 64 KB
• Interface Type: CAN, I2C, SPI, USART
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 112
• Number Of Timers: 8
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWARM, EWARM-BL, KSDK-STM32-PLUS, KSK-STM32F103ZE, MDK-ARM, RL-ARM, ULINK2
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 3 (12 bit, 16 Channel)
• On-chip Dac: 2 (12 bit, 2 Channel)
• Featured Product: STM32 Cortex-M3 Companion Products
• Eeprom Size: -
• A/d Bit Size: 12 bit
• A/d Channels Available: 16
• Height: 1.4 mm
• Length: 20 mm
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2 V
• Width: 20 mm
• For Use With: 497-10048 - BOARD EVAL ACCELEROMETER497-10030 - STARTER KIT FOR STM32497-9048 - BOARD DEMO BASED ON STM32F103ZEKSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8511 - KIT STARTER FOR STM32 512K FLASH497-8505 - KIT STARTER FOR STM32F10XE MCU497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2MCBSTM32 - BOARD EVAL FOR STM STM32X SER497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

STM32F103xC, STM32F103xD, STM32F103xE
Note:
same size. The crystal manufacturer typically specifies a load capacitance which is the
series combination of C
can be used as a rough estimate of the combined pin and board capacitance) when sizing
C
microcontrollers” available from the ST website www.st.com.
Figure 22. Typical application with an 8 MHz crystal
1. R
Low-speed external clock generated from a crystal/ceramic resonator
The low-speed external (LSE) clock can be supplied with a 32.768 kHz crystal/ceramic
resonator oscillator. All the information given in this paragraph are based on characterization
results obtained with typical external components specified in
the resonator and the load capacitors have to be placed as close as possible to the oscillator
pins in order to minimize output distortion and startup stabilization time. Refer to the crystal
resonator manufacturer for more details on the resonator characteristics (frequency,
package, accuracy).
Table 24.
1. Based on characterization, not tested in production.
2. Refer to the note and caution paragraphs below the table, and to the application note AN2867 “Oscillator
3. The oscillator selection can be optimized in terms of supply current using an high quality resonator with
4.
For C
15 pF range selected to match the requirements of the crystal or resonator (see
C
capacitance which is the series combination of C
Load capacitance C
t
SU(LSE)
L1
L1
Symbol
design guide for ST microcontrollers”.
small R
32.768 kHz oscillation is reached. This value is measured for a standard crystal resonator and it can vary
significantly with the crystal manufacturer
C
t
R
g
and C
SU(LSE)
and C
EXT
I
(2)
2
m
F
L1
value depends on the crystal characteristics.
(4)
and C
Resonator with
integrated capacitors
S
L2
L2,
is the startup time measured from the moment it is enabled (by software) to a stabilized
value for example MSIV-TIN32.768kHz. Refer to crystal manufacturer for more details
Feedback resistor
Recommended load capacitance
versus equivalent serial
resistance of the crystal (R
LSE driving current
Oscillator transconductance
Startup time
. Refer to the application note AN2867 “Oscillator design guide for ST
LSE oscillator characteristics (f
are usually the same size. The crystal manufacturer typically specifies a load
L2
, it is recommended to use high-quality ceramic capacitors in the 5 pF to
C L2
C L1
L
Parameter
has the following formula: C
L1
and C
8 MH z
resonator
R EXT (1)
Doc ID 14611 Rev 7
L2
. PCB and MCU pin capacitance must be included (10 pF
S
)
OSC_OU T
(3)
OSC_IN
V
DD
V
R F
LSE
= 3.3 V, V
DD
Conditions
R
L1
S
L
is stabilized
= 32.768 kHz)
controlled
= 30 k
= C
and C
Bias
gain
L1
IN
x C
L2
= V
.
L2
SS
Table
/ (C
STM32F103xx
(1)
Electrical characteristics
Min
5
L1
f HSE
24. In the application,
+ C
Typ
5
3
L2
) + C
Max
1.4
15
Figure
stray
ai14145
where
57/123
µA/V
Unit
M
pF
µA
23).
s