MC908QY4ACDWE Freescale Semiconductor, MC908QY4ACDWE Datasheet - Page 86

• Manufacturer Part Number: MC908QY4ACDWE
• Description: IC MCU 8BIT 4K FLASH 16-SOIC
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908QY4ACDWE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Peripherals: LVD, POR, PWM
• Number Of I /o: 13
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 16-SOIC (0.300", 7.5mm Width)
• Processor Series: HC08QY
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 13
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, M68CBL05AE, DEMO908QB8, DEMO908QC16
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 6 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Connectivity: -
• Lead Free Status / Rohs Status: Details

Keyboard Interrupt Module (KBI)
9.3.2 Keyboard Initialization
When a keyboard interrupt pin is enabled, it takes time for the internal pullup or pulldown device to pull
the pin to its deasserted level. Therefore a false interrupt can occur as soon as the pin is enabled.
To prevent a false interrupt on keyboard initialization:
An interrupt signal on an edge sensitive pin can be acknowledged immediately after enabling the pin. An
interrupt signal on an edge and level sensitive pin must be acknowledged after a delay that depends on
the external load.
9.4 Interrupts
The following KBI source can generate interrupt requests:
9.5 Low-Power Modes
The WAIT and STOP instructions put the MCU in low power-consumption standby modes.
9.5.1 Wait Mode
The KBI module remains active in wait mode. Clearing IMASKK in KBSCR enables keyboard interrupt
requests to bring the MCU out of wait mode.
9.5.2 Stop Mode
The KBI module remains active in stop mode. Clearing IMASKK in KBSCR enables keyboard interrupt
requests to bring the MCU out of stop mode.
9.6 KBI During Break Interrupts
The system integration module (SIM) controls whether status bits in other modules can be cleared during
the break state. The BCFE bit in the break flag control register (BFCR) enables software to clear status
bits during the break state. See BFCR in the SIM section of this data
To allow software to clear status bits during a break interrupt, write a 1 to BCFE. If a status bit is cleared
during the break state, it remains cleared when the MCU exits the break state.
To protect status bits during the break state, write a 0 to BCFE. With BCFE cleared (its default state),
software can read and write registers during the break state without affecting status bits. Some status bits
have a two-step read/write clearing procedure. If software does the first step on such a bit before the
break, the bit cannot change during the break state as long as BCFE is cleared. After the break, doing the
second step clears the status bit.
86
1. Mask keyboard interrupts by setting IMASKK in KBSCR.
2. Enable the KBI polarity by setting the appropriate KBIPx bits in KBIPR.
3. Enable the KBI pins by setting the appropriate KBIEx bits in KBIER.
4. Write to ACKK in KBSCR to clear any false interrupts.
5. Clear IMASKK.
•
Keyboard flag (KEYF) — The KEYF bit is set when any enabled KBI pin is asserted based on the
KBI mode and pin polarity. The keyboard interrupt mask bit, IMASKK, is used to enable or disable
KBI interrupt requests.
MC68HC908QYA/QTA Family Data Sheet, Rev. 3
sheet.
Freescale Semiconductor