R5F21334CNFP#U0 Renesas Electronics America, R5F21334CNFP#U0 Datasheet - Page 378

• Manufacturer Part Number: R5F21334CNFP#U0
• Description: MCU 1KB FLASH 16K ROM 32-LQFP
• Manufacturer: Renesas Electronics America
• Series: R8C/3x/33Cr

Specifications of R5F21334CNFP#U0

• Core Processor: R8C
• Core Size: 16/32-Bit
• Speed: 20MHz
• Connectivity: I²C, LIN, SIO, SSU, UART/USART
• Peripherals: POR, PWM, Voltage Detect, WDT
• Number Of I /o: 27
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 12x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 32-LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

R8C/33C Group
REJ09B0570-0100 Rev.1.00 Dec. 14, 2009
Page 348 of 589
Figure 22.8
22.4.1
Table 22.8
Note:
Bit Rate
115200
14400
19200
28800
38400
57600
(bps)
1200
2400
4800
9600
Receive Timing Example When Transfer Data 8 Bits is Long (Parity Disabled, One Stop Bit)
1. For the high-speed on-chip oscillator, the correction value in the FRA4 register should be written into the FRA1
S2RIC register
In UART mode, the bit rate is the frequency divided by the U2BRG register divided by 16. Table 22.8 lists the
Bit Rate Setting Example in UART Mode (Internal Clock Selected).
U2C1 register
U2C1 register
Transfer clock
register and the correction value in the FRA5 register should be written into the FRA3 register.
This applies when the high-speed on-chip oscillator is selected as the system clock and bits FRA22 to FRA20
in the FRA2 register are set to 000b (divide-by-2 mode). For the precision of the high-speed on-chip oscillator,
refer to 32. Electrical Characteristics .
count source
U2BRG
Source
RE bit in
Count
U2BRG
RI bit in
IR bit in
Bit Rate
RXD2
RTS2
f8
f8
f8
f1
f1
f1
f1
f1
f1
f1
Bit Rate Setting Example in UART Mode (Internal Clock Selected)
Receive Timing in UART Mode
The above applies when:
• PRYE bit in U2MR register = 0 (parity disabled)
• STPS bit in U2MR register = 0 (one stop bit)
• CRD bit in U2C0 register = 0 (CTS2/RTS2 function enabled), CRS bit = 1 (RTS2 function selected)
129 (81h)
129 (81h)
42 (2Ah)
10 (0Ah)
64 (40h)
32 (20h)
86 (56h)
64 (40h)
32 (20h)
21 (15h)
U2BRG
Setting
Value
System Clock = 20 MHz
Reception starts when a transfer clock
is generated at the falling edge
of the start bit.
Actual Time
Start bit
113636.36
14367.82
19230.77
29069.77
37878.79
56818.18
(bps)
1201.92
2403.85
4734.85
9615.38
“L” is determined.
Setting
Error
(%)
-1.36 29 (1Dh)
-0.22 79 (4Fh)
-1.36 29 (1Dh)
-1.36 19 (13h)
-1.36
0.16 119 (77h)
0.16 59 (3Bh)
0.16 119 (77h)
0.16 59 (3Bh)
0.94 39 (27h)
System Clock = 18.432 MHz
U2BRG
9 (09h)
Setting
D0
Value
Set to 0 when an interrupt request is acknowledged or by a program.
Receive data taken in
Data transfer from UART2 receive register
to U2RB register
Actual Time
115200.00
14400.00
19200.00
28800.00
38400.00
57600.00
(bps)
2400.00
4800.00
1200.00
9600.00
D1
D7
Setting
Error
(%)
0.00 51 (33h)
0.00 25 (19h)
0.00 12 (0Ch)
0.00 51 (33h)
0.00 34 (22h) 14285.71
0.00 25 (19h) 19230.77
0.00 16 (10h) 29411.76
0.00 12 (0Ch) 38461.54
0.00
0.00
(1)
U2BRG
22. Serial Interface (UART2)
Setting
8 (08h)
Value
Stop bit
System Clock = 8 MHz
−
55555.56
1201.92
2403.85
4807.69
9615.38
Actual
(bps)
Time
−
Setting
Error
(%)
-0.79
-3.55
0.16
0.16
0.16
0.16
0.16
2.12
0.16
−