R5F21334CNFP#U0 Renesas Electronics America, R5F21334CNFP#U0 Datasheet - Page 382

• Manufacturer Part Number: R5F21334CNFP#U0
• Description: MCU 1KB FLASH 16K ROM 32-LQFP
• Manufacturer: Renesas Electronics America
• Series: R8C/3x/33Cr

Specifications of R5F21334CNFP#U0

• Core Processor: R8C
• Core Size: 16/32-Bit
• Speed: 20MHz
• Connectivity: I²C, LIN, SIO, SSU, UART/USART
• Peripherals: POR, PWM, Voltage Detect, WDT
• Number Of I /o: 27
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 12x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 32-LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

R8C/33C Group
REJ09B0570-0100 Rev.1.00 Dec. 14, 2009
Page 352 of 589
22.5
Table 22.9
Notes:
Transfer data format
Transfer clock
Transmit start conditions
Receive start conditions
Interrupt request generation
timing
Error detection
Selectable functions
I
Specifications. Tables 22.10 and 22.11 list the registers used in I
Mode Functions, Figure 22.13 shows an I
Register and Interrupt Timing.
As shown in Table 22.12, the MCU is placed in I
to 1. Because SDA2 transmit output has a delay circuit attached, SDA2 output does not change state until SCL2
goes low and remains stably low.
2
1. When an external clock is selected, the requirements must be met while the external clock is held high.
2. If an overrun error occurs, the received data in the U2RB register will be undefined. The IR bit in the S2RIC
C mode is provided for use as a simplified I
register remains unchanged.
Special Mode 1 (I
Item
I
2
C Mode Specifications
2
Transfer data length: 8 bits
• Master mode
• Slave mode
To start transmission, the following requirements must be met:
• The TE bit in the U2C1 register is set to 1 (transmission enabled).
• The TI bit in the U2C1 register is set to 0 (data present in the U2TB register).
To start reception, the following requirements must be met:
• The RE bit in the U2C1 register is set to 1 (reception enabled).
• The TE bit in the U2C1 register is set to 1 (transmission enabled).
• The TI bit in the U2C1 register is set to 0 (data present in the U2TB register).
Start/stop condition detection, no acknowledgement detection, or acknowledgement
detection
Overrun error
• SDA2 digital delay
• Clock phase setting
C Mode)
The CKDIR bit in the U2MR register is set to 0 (internal clock): fj/(2(n+1))
fj = f1, f8, f32, fC n = setting value in the U2BRG register: 00h to FFh
The CKDIR bit is set to 1 (external clock): Input from the SCL2 pin
No digital delay or a delay of 2 to 8 U2BRG count source clock cycles
can be selected.
With or without clock delay can be selected.
This error occurs if the serial interface starts receiving the next unit of data before
reading the U2RB register and receives the 8th bit of the next unit of data.
2
C Mode Block Diagram, and Figure 22.14 shows the Transfer to U2RB
(2)
2
2
C mode by setting bits SMD2 to SMD0 to 010b and the IICM bit
C interface compatible mode. Table 22.9 lists the I
2
C mode and the settings. Table 22.12 lists the I
Specification
22. Serial Interface (UART2)
(1)
(1)
2
C Mode
2
C