R5F21334CNFP#U0 Renesas Electronics America, R5F21334CNFP#U0 Datasheet - Page 441

• Manufacturer Part Number: R5F21334CNFP#U0
• Description: MCU 1KB FLASH 16K ROM 32-LQFP
• Manufacturer: Renesas Electronics America
• Series: R8C/3x/33Cr

Specifications of R5F21334CNFP#U0

• Core Processor: R8C
• Core Size: 16/32-Bit
• Speed: 20MHz
• Connectivity: I²C, LIN, SIO, SSU, UART/USART
• Peripherals: POR, PWM, Voltage Detect, WDT
• Number Of I /o: 27
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 12x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 32-LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

R8C/33C Group
REJ09B0570-0100 Rev.1.00 Dec. 14, 2009
Page 411 of 589
25.2.7
Notes:
After Reset
1. When rewriting the SDAO bit, write 0 to the SDAOP bit simultaneously using the MOV instruction.
2. Do not write to the SDAO bit during a transfer operation.
3. Enabled in master mode. When writing to the BBSY bit, write 0 to the SCP bit simultaneously using the MOV
4. Disabled when the clock synchronous serial format is used.
Bit
b0
b1
b2
b3
b4
b5
b6
b7
Address 0199h
instruction. Execute the same way when a start condition is regenerated.
Symbol
SDAOP SDAO write protect bit
Symbol
IICRST I
SDAO
Bit
SCLO
BBSY
SCP
IIC bus Control Register 2 (ICCR2)
—
—
BBSY
b7
0
Nothing is assigned. If necessary, set to 0. When read, the content is 1.
Nothing is assigned. If necessary, set to 0. When read, the content is 1.
SCL monitor flag
SDA output value control bit
Start/stop condition generation
disable bit
Bus busy bit
2
C bus control block reset bit
SCP
b6
1
Bit Name
(4)
SDAO
b5
1
SDAOP
b4
1
When hang-up occurs due to communication failure during
I
block of the I
initializing registers.
0: SCL pin is set to “L”
1: SCL pin is set to “H”
When rewriting the SDAO bit, write 0 simultaneously
When read, the content is 1.
When read
0: SDA pin output is held “L”
1: SDA pin output is held “H”
When written
0: SDA pin output is changed to “L”
1: SDA pin output is changed to high-impedance
When writing to the to BBSY bit, write 0 simultaneously
When read, the content is 1.
Writing 1 is invalid.
When read:
0: Bus is released
1: Bus is occupied
When written
0: Stop condition generated
1: Start condition generated
2
C bus interface operation, writing 1 resets the control
(“H” output via external pull-up resistor)
(SDA signal changes from “L” to “H”
while SCL signal is held “H”)
(SDA signal changes from “H” to “L”
while SCL signal is held “H”)
SCLO
b3
1
2
C bus interface without setting ports or
(1, 2)
(3)
:
b2
—
1
Function
IICRST
b1
0
b0
—
1
25. I
2
C bus Interface
(1)
.
(3)
.
R/W
R/W
R/W
R/W
R/W
R/W
—
—
R