R5F21275SNFP#U0 Renesas Electronics America, R5F21275SNFP#U0 Datasheet - Page 387

• Manufacturer Part Number: R5F21275SNFP#U0
• Description: IC R8C/27 MCU FLASH 32LQFP
• Manufacturer: Renesas Electronics America
• Series: R8C/2x/27r

Specifications of R5F21275SNFP#U0

• Core Processor: R8C
• Core Size: 16/32-Bit
• Speed: 20MHz
• Connectivity: I²C, LIN, SIO, SSU, UART/USART
• Peripherals: LED, POR, Voltage Detect, WDT
• Number Of I /o: 25
• Program Memory Size: 24KB (24K x 8)
• Program Memory Type: FLASH
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 2.2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 32-LQFP
• For Use With: R0K521276S000BE - KIT DEV RSK-R8C/26-29R0E521000EPB00 - PROBE EMULATOR FOR PC7501
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

R8C/26 Group, R8C/27 Group
Rev.2.10
REJ09B0278-0210
Figure 19.12
19.4.3.4
The program command writes data to the flash memory in 1-byte units.
By writing 40h in the first bus cycle and data in the second bus cycle to the write address, an auto-program
operation (data program and verify) will start. Make sure the address value specified in the first bus cycle is the
same address as the write address specified in the second bus cycle.
The FMR00 bit in the FMR0 register can be used to determine whether auto-programming has completed.
When suspend function disabled, the FMR00 bit is set to 0 during auto-programming and set to 1 when auto-
programming completes.
When suspend function enabled, the FMR44 bit is set to 1 during auto-programming and set to 0 when auto-
programming completes.
The FMR06 bit in the FMR0 register can be used to determine the result of auto-programming after it has been
finished (refer to 19.4.5 Full Status Check).
Do not write additions to the already programmed addresses.
When the FMR02 bit in the FMR0 register is set to 0 (rewriting disabled) or the FMR02 bit is set to 1 (rewriting
enabled) and the FMR15 bit in the FMR1 register is set to 1 (rewriting disabled), program commands targeting
block 0 are not acknowledged. When the FMR16 bit is set to 1 (rewriting disabled), program commands
targeting block 1 are not acknowledged.
Figure 19.12 shows the Program Command (When Suspend Function Disabled). Figure 19.13 shows the
Program Command (When Suspend Function Enabled).
In EW1 mode, do not execute this command for any address which a rewrite control program is allocated.
In EW0 mode, the MCU enters read status register mode at the same time auto-programming starts and the
status register can be read. The status register bit 7 (SR7) is set to 0 at the same time auto-programming starts
and set back to 1 when auto-programming completes. In this case, the MCU remains in read status register
mode until the next read array command is written. The status register can be read to determine the result of
auto-programming after auto-programming has completed.
Sep 26, 2008
Program Command
Program Command (When Suspend Function Disabled)
Page 368 of 453
Write the command code 40h to
Write data to the write address
Program completed
the write address
Full status check
FMR00 = 1?
Start
Yes
No
19. Flash Memory