HD64F3644H Renesas Electronics America, HD64F3644H Datasheet - Page 157

• Manufacturer Part Number: HD64F3644H
• Description: IC H8 MCU FLASH 32K 64-QFP
• Manufacturer: Renesas Electronics America
• Series: H8® H8/300Lr

Specifications of HD64F3644H

• Core Processor: H8/300L
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI
• Peripherals: PWM, WDT
• Number Of I /o: 53
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 64-QFP
• Package: 64PQFP
• Family Name: H8
• Maximum Speed: 8 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 45
• Interface Type: SCI
• On-chip Adc: 8-chx8-bit
• Number Of Timers: 4
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

Sample Program for Erasing One Block
This program uses the following registers:
R0:
R1H: Stores read data. Also used in dummy write.
R2:
R3:
R4:
R5:
R6L: Used for prewrite-verify and erase-verify fail count.
The values of #a, #b, #c, #d, and #e in the program depend on the operating frequency. They
should be set as indicated in tables 6.11 and 6.12. Erase block register (EBR1, EBR2) settings
should be made as indicated in sections 6.5.2 and 6.5.3 in section 6.5, Flash Memory Register
Descriptions. For #BLKSTR and #BLKEND, the start address and end address corresponding to
the set erase block register should be set as indicated in table 6.7.
FLMCR:
EBR1:
EBR2:
TCSRW:
TCW:
; #
; #
;
Execute prewrite
BLKSTR is start address of block to be erased
BLKEND is last address of block to be erased
Used for erase block specification. Also stores address used in prewrite and erase-verify.
Stores last address of block to be erased.
Stores address used in prewrite and erase-verify.
Used for prewrite, prewrite-verify, erase, and erase-verify loop counter value setting. Also
stores register set values.
Used for prewrite and erase loop counter value setting.
.EQU
.EQU
.EQU
.EQU
.EQU
.ALIGN 2
MOV.B #H'**,
MOV.B R0H,
MOV.W #BLKSTR, R0
MOV.W #BLKEND, R2
ADDS
MOV.W R0,
H'FF80
H'FF82
H'FF83
H'FFBE
H'FFBF
#1,
R0H
@EBR*:8
R2
R3
;
;
;
;
;
;
Set EBR
Start address of block to be erased
Last address of block to be erased
Last address of block to be erased + 1
Start address of block to be erased
*
Rev. 6.00 Sep 12, 2006 page 135 of 526
REJ09B0326-0600
Section 6 ROM
R2