M30626SPFP#U5C Renesas Electronics America, M30626SPFP#U5C Datasheet - Page 259

IC M16C/62P MCU ROMLESS 100QFP

M30626SPFP#U5C

Manufacturer Part Number
M30626SPFP#U5C
Description
IC M16C/62P MCU ROMLESS 100QFP
Manufacturer
Renesas Electronics America
Series
M16C™ M16C/60r
Datasheet

Specifications of M30626SPFP#U5C

Core Processor
M16C/60
Core Size
16-Bit
Speed
24MHz
Connectivity
I²C, IEBus, UART/USART
Peripherals
DMA, WDT
Number Of I /o
50
Program Memory Type
ROMless
Ram Size
31K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Data Converters
A/D 26x10b; D/A 2x8b
Oscillator Type
Internal
Operating Temperature
-20°C ~ 85°C
Package / Case
100-QFP
For Use With
867-1000 - KIT QUICK START RENESAS 62PR0K33062PS001BE - R0K33062P STARTER KITR0K33062PS000BE - KIT EVAL STARTER FOR M16C/62PM3062PT3-CPE-3 - EMULATOR COMPACT M16C/62P/30P
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Program Memory Size
-

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M30626SPFP#U5CM30626SPFP#U3C
Manufacturer:
TOSHIBA
Quantity:
101
Company:
Part Number:
M30626SPFP#U5CM30626SPFP#U3C
Manufacturer:
Renesas Electronics America
Quantity:
10 000
Company:
Part Number:
M30626SPFP#U5C
Manufacturer:
Renesas Electronics America
Quantity:
10 000
M16C/62P Group (M16C/62P, M16C/62PT)
Rev.2.41
REJ09B0185-0241
18.1.3
Table 18.4
NOTES:
Function
A/D Conversion Start
Condition
A/D Conversion Stop
Condition
Interrupt Request
Generation timing
Analog Input Pin
Reading of Result of A/D
Converter
1. AN0_0 to AN0_7, and AN2_0 to AN2_7 can be used in the same way as AN0 to AN7. However, if
In single sweep mode, analog voltage that is applied to selected pins is converted one-by-one to a digital code.
Table 18.4 shows the Single Sweep Mode Specifications. Figure 18.7 shows the ADCON0 Register and
ADCON1 Register (Single Sweep Mode).
VCC2 < VCC1, do not use AN0_0 to AN0_7 and AN2_0 to AN2_7 as analog input pins.
Jan 10, 2006
Single Sweep Mode
Item
Single Sweep Mode Specifications
Page 242 of 390
The SCAN1 to SCAN0 bits in the ADCON1 register and the ADGSEL1 to
ADGSEL0 bits in the ADCON2 register select pins. Analog voltage applied to
this pins is converted one-by-one to a digital code.
• When the TRG bit in the ADCON0 register is “0” (software trigger)
• When the TRG bit is “1” (ADTRG trigger)
• Completion of A/D conversion (If a software trigger is selected, the ADST bit
• Set the ADST bit to “0”
Completion of A/D conversion
Select from AN0 to AN1 (2 pins), AN0 to AN3 (4 pins), AN0 to AN5 (6 pins),
AN0 to AN7 (8 pin)
Read one of the AD0 to AD7 registers that corresponds to the selected pin
is cleared to “0” (A/D conversion halted))
The ADST bit in the ADCON0 register is set to “1” (A/D conversion starts)
Input on the ADTRG pin changes state from high to low after the ADST bit is
set to “1” (A/D conversion starts)
(1)
Specification
18. A/D Converter

Related parts for M30626SPFP#U5C