MC68HC711E9CFNE2 Freescale Semiconductor, MC68HC711E9CFNE2 Datasheet - Page 332

IC MCU 8BIT 512RAM 52-PLC

MC68HC711E9CFNE2

Manufacturer Part Number
MC68HC711E9CFNE2
Description
IC MCU 8BIT 512RAM 52-PLC
Manufacturer
Freescale Semiconductor
Series
HC11r
Datasheet

Specifications of MC68HC711E9CFNE2

Core Processor
HC11
Core Size
8-Bit
Speed
2MHz
Connectivity
SCI, SPI
Peripherals
POR, WDT
Number Of I /o
38
Program Memory Size
12KB (12K x 8)
Program Memory Type
OTP
Eeprom Size
512 x 8
Ram Size
512 x 8
Voltage - Supply (vcc/vdd)
4.5 V ~ 5.5 V
Data Converters
A/D 8x8b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
52-PLCC
Processor Series
HC711E
Core
HC11
Data Bus Width
8 bit
Data Ram Size
512 B
Interface Type
SCI, SPI
Maximum Clock Frequency
2 MHz
Number Of Programmable I/os
38
Number Of Timers
8
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 40 C
On-chip Adc
8 bit
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MC68HC711E9CFNE2
Manufacturer:
TE
Quantity:
12 000
Part Number:
MC68HC711E9CFNE2
Manufacturer:
FREESCAL
Quantity:
5 530
Part Number:
MC68HC711E9CFNE2
Manufacturer:
FREESCALE
Quantity:
1 133
Engineering Bulletin
Programming Procedure
Step 1
Step 2
332
Once you have obtained PCbug11, use this step-by-step procedure to
program your MC68HC711E9 part.
Also take note of P4 connector pin 18. In step 5, you will connect a +12-
volt (at most +12.5 volts) programming voltage through a 100- current
limiting resistor to the XIRQ pin. Do not connect this programming
voltage until you are instructed to do so in step 5.
Before applying power to the EVBU, remove the jumper from J7
and place it across J3 to ground the MODB pin.
Place a jumper across J4 to ground the MODA pin. This will force
the EVBU into special bootstrap mode on power up.
Remove the resident MC68HC11E9 MCU from the EVBU.
Place your MC68HC711E9 in the open socket with the notched
corner of the part aligned with the notch on the PLCC socket.
Connect the EVBU to one of your PC COM ports. Apply +5 volts
to V
From a DOS command line prompt, start PCbug11 with
– C:\PCBUG11\> PCBUG11 –E PORT = 1
– C:\PCBUG11\> PCBUG11 –E PORT = 2
PCbug11 only supports COM ports 1 and 2. If you have made the
proper connections and have a high quality cable, you should
quickly get a PCbug11 command prompt. If you do receive a
Comms fault error, check your cable and board connections.
Most PCbug11 communications problems can be traced to poorly
made cables or bad board connections.
with the EVBU connected to COM1
with the EVBU connected to COM2
DD
and ground to GND on the power connector of your EVBU.
MOTOROLA
EB296

Related parts for MC68HC711E9CFNE2