HD64F2638F20J Renesas Electronics America, HD64F2638F20J Datasheet - Page 1012

• Manufacturer Part Number: HD64F2638F20J
• Description: IC H8S MCU FLASH 256K 128-QFP
• Manufacturer: Renesas Electronics America
• Series: H8® H8S/2600r

Specifications of HD64F2638F20J

• Core Processor: H8S/2600
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: CAN, SCI, SmartCard
• Peripherals: Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 72
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 12x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 128-QFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

Section 23B Power-Down Modes [HD64F2636UF, HD6432636UF, HD64F2638UF, HD6432638UF,
HD64F2638WF, HD6432638WF, HD64F2639UF, HD6432639UF, HD64F2639WF, HD6432639WF,
HD64F2630UF, HD6432630UF, HD64F2630WF, HD6432630WF, HD6432635F, HD64F2635F, HD6432634F]
MSTPCRA/MSTPCRB/MSTPCRC Bits 7 to 0, MSTPCRD Bits 7 and 6—Module Stop
(MSTPA7 to MSTPA0, MSTPB7 to MSTPB0, MSTPC7 to MSTPC0, MSTPD7 and
MSTPD6): These bits specify module stop mode. See table 23B-5 for the method of selecting the
on-chip peripheral functions.
MSTPCRA/MSTPCRB/
MSTPCRC Bits 7 to 0,
MSTPCRD Bits 7 and 6
MSTPA7 to MSTPA0,
MSTPB7 to MSTPB0,
MSTPC7 to MSTPC0,
MSTPD7 and MSTPD6 Description
0
1
23B.3 Medium-Speed Mode
In high-speed mode, when the SCK2 to SCK0 bits in SCKCR are set to 1, the operating mode
changes to medium-speed mode as soon as the current bus cycle ends. In medium-speed mode, the
CPU operates on the operating clock (φ/2, φ/4, φ/8, φ/16, or φ/32) specified by the SCK2 to SCK0
bits. The bus masters other than the CPU (DTC) also operate in medium-speed mode. On-chip
supporting modules other than the bus masters always operate on the high-speed clock (φ).
In medium-speed mode, a bus access is executed in the specified number of states with respect to
the bus master operating clock. For example, if φ/4 is selected as the operating clock, on-chip
memory is accessed in 4 states, and internal I/O registers in 8 states.
Medium-speed mode is cleared by clearing all of bits SCK2 to SCK0 to 0. A transition is made to
high-speed mode and medium-speed mode is cleared at the end of the current bus cycle.
If a SLEEP instruction is executed when the SSBY bit in SBYCR is cleared to 0, and LSON bit in
LPWRCR is cleared to 0, a transition is made to sleep mode. When sleep mode is cleared by an
interrupt, medium-speed mode is restored.
When the SLEEP instruction is executed with the SSBY bit = 1, LPWRCR LSON bit = 0, and
TCSR (WDT1) PSS bit = 0, operation shifts to the software standby mode. When software
standby mode is cleared by an external interrupt, medium-speed mode is restored.
When the RES pin is set low and medium-speed mode is cancelled, operation shifts to the reset
state. The same applies in the case of a reset caused by overflow of the watchdog timer.
Page 962 of 1458
Module stop mode is cleared (initial value of MSTPA7 and MSTPA6)
Module stop mode is set (initial value of MSTPA5–0, MSTPB7–0,
MSTPC7–0, and MSTPC7, 6)
H8S/2639, H8S/2638, H8S/2636,
REJ09B0103-0800 Rev. 8.00
H8S/2630, H8S/2635 Group
May 28, 2010