ATMEGA103-6AC Atmel, ATMEGA103-6AC Datasheet - Page 104

• Manufacturer Part Number: ATMEGA103-6AC
• Description: IC MCU 128K 6MHZ A/D 64TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA103-6AC

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 6MHz
• Connectivity: SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 128KB (64K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 64-TQFP, 64-VQFP
• For Use With: ATSTK501 - ADAPTER KIT FOR 64PIN AVR MCU
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Memory
Programming
Program and Data
Memory Lock Bits
Fuse Bits
Signature Bytes
Programming the Flash
and EEPROM
104
ATmega103(L)
The ATmega103(L) MCU provides two Lock bits that can be left unprogrammed (“1”) or
can be programmed (“0”) to obtain the additional features listed in Table 35. The Lock
bits can only be erased to “1” with the Chip Erase command.
Table 35. Lock Bit Protection Modes
Note:
The ATmega103(L) has four Fuse bits, SPIEN, SUT1..0 and EESAVE.
•
•
•
The status of the Fuse bits is not affected by Chip Erase.
All Atmel microcontrollers have a 3-byte signature code that identifies the device. This
code can be read in both Serial and Parallel mode. The three bytes reside in a separate
address space.
For the ATmega103 they are:
1. $000: $1E (indicates manufactured by Atmel)
2. $001: $97 (indicates 128K bytes Flash memory)
3. $002: $01 (indicates ATmega103 when signature byte $001 is $97)
Atmel’s ATmega103(L) offers 128K bytes of In-System Reprogrammable Flash memory
and 4K bytes of EEPROM Data memory.
The ATmega103(L) is shipped with the On-chip Flash Program and EEPROM Data
memory arrays in the erased state (i.e., contents = $FF) and ready to be programmed.
This device supports a Parallel Programming mode and a Serial Programming mode.
The +12V supplied to the RESET pin in Parallel Programming mode is used for pro-
gramming enable only, and no current of significance is drawn by this pin. The Serial
Programming mode provides a convenient way to download program and data into the
ATmega103(L) inside the user’s system.
Mode
Memory Lock Bits
1
2
3
When the SPIEN Fuse is programmed (“0”), Serial Program and Data Downloading
is enabled. Default value is programmed (“0”). The SPIEN Fuse is not accessible in
Serial Programming mode.
When EESAVE is programmed, the EEPROM memory is preserved through the
Chip Erase cycle. Default value is unprogrammed (“1”). The EESAVE Fuse bit
cannot be programmed if any of the Lock bits are programmed.
SUT1..0 Fuses: Determine the MCU start-up time. See Table 5 on page 27 for
further details. Default value is unprogrammed (“11”), which gives a nominal start-up
time of 16 ms.
1. In Parallel mode, programming of the Fuse bits are also disabled. Program the Fuse
LB1
bits before programming the Lock bits.
1
0
0
LB2
1
1
0
Protection Type
No memory lock features enabled.
Further programming of the Flash and EEPROM is disabled.
Same as mode 2, and verify is also disabled.
0945I–AVR–02/07
(1)