ATMEGA88PA-MU Atmel, ATMEGA88PA-MU Datasheet - Page 31

• Manufacturer Part Number: ATMEGA88PA-MU
• Description: MCU AVR 8K ISP FLASH MEM 32-QFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA88PA-MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 23
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Controller Family/series: AVR MEGA
• No. Of I/o's: 23
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 1KB
• Cpu Speed: 20MHz
• No. Of Timers: 3
• Rohs Compliant: Yes
• Package: 32QFN EP
• Device Core: AVR
• Family Name: ATmega
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 23
• Interface Type: SPI/TWI/USART
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 3
• For Use With: ATSTK600-TQFP32 - STK600 SOCKET/ADAPTER 32-TQFPATSTK600-DIP40 - STK600 SOCKET/ADAPTER 40-PDIP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATAVRISP2 - PROGRAMMER AVR IN SYSTEMATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

8271C–AVR–08/10
Figure 8-3.
Table 8-6.
Notes:
ATmega48A/48PA/88A/88PA/168A/168PA/328/328
Oscillator Source /
Power Conditions
Ceramic resonator, fast
rising power
Ceramic resonator, slowly
rising power
Ceramic resonator, BOD
enabled
Ceramic resonator, fast
rising power
Ceramic resonator, slowly
rising power
Crystal Oscillator, BOD
enabled
Crystal Oscillator, fast
rising power
Crystal Oscillator, slowly
rising power
1. These options should only be used when not operating close to the maximum frequency of the
2. These options are intended for use with ceramic resonators and will ensure frequency stability
device, and only if frequency stability at start-up is not important for the application. These
options are not suitable for crystals.
at start-up. They can also be used with crystals when not operating close to the maximum fre-
quency of the device, and if frequency stability at start-up is not important for the application.
Crystal Oscillator Connections
Start-up Times for the Full Swing Crystal Oscillator Clock Selection
Start-up Time from
Power-down and
C2
C1
Power-save
16K CK
16K CK
16K CK
258 CK
258 CK
1K CK
1K CK
1K CK
XTAL2 (TOSC2)
XTAL1 (TOSC1)
GND
Additional Delay
14CK + 4.1 ms
14CK + 4.1 ms
14CK + 65 ms
14CK + 65 ms
14CK + 4.1 ms
14CK + 65 ms
(V
from Reset
CC
14CK
14CK
= 5.0V)
(2)
(1)
(2)
(1)
(2)
CKSEL0
0
0
0
0
1
1
1
1
SUT1...0
00
01
10
11
00
01
10
11
31