ATMEGA8HVD-4MX Atmel, ATMEGA8HVD-4MX Datasheet - Page 42
ATMEGA8HVD-4MX
Manufacturer Part Number
ATMEGA8HVD-4MX
Description
MCU AVR 8K FLASH 2.1-8V 4MHZ QFN
Manufacturer
Atmel
Series
AVR® ATmegar
Datasheet
1.ATMEGA8HVD-4MX.pdf
(168 pages)
Specifications of ATMEGA8HVD-4MX
Core Processor
AVR
Core Size
8-Bit
Speed
4MHz
Peripherals
POR, WDT
Number Of I /o
5
Program Memory Size
8KB (4K x 16)
Program Memory Type
FLASH
Eeprom Size
256 x 8
Ram Size
512 x 8
Voltage - Supply (vcc/vdd)
2 V ~ 2.4 V
Data Converters
A/D 1x10b
Oscillator Type
Internal
Operating Temperature
-20°C ~ 85°C
Package / Case
18-MLF® Exposed Pad (Staggered Leads), DFN
For Use With
ATSTK600 - DEV KIT FOR AVR/AVR32ATSTK500 - PROGRAMMER AVR STARTER KIT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Connectivity
-
- Current page: 42 of 168
- Download datasheet (3Mb)
10.6
10.6.1
42
ATmega4HVD/8HVD Start-up Sequence
ATmega4HVD/8HVD
Start-up with one FET connected
Figure 10-7. Black-out Reset with high current consumption at V
The Voltage Regulator will not start until it is enabled by the Charger Detect module. Before
this happens the chip will be in Power-off mode and only the Charger Detect module is
enabled. In order for the Charger Detect module to enable the Voltage Regulator, the V
voltage must exceed the Power-On Threshold, V
the Voltage Regulator starts up and a Power-On Reset forces the chip into RESET state.
During start-up with only one FET (D-FET), cell charging through the body diode of the Dis-
charge FET will start immediately when a charger is connected, even if the chip has not
started yet. The voltage on the BATT pin equals the cell voltage (VFET) plus a diode drop dur-
ing the complete start-up sequence, and will hence increase as the cell is being charged.
A typical start-up sequence for the application is illustrated in
Figure 10-8. Powering up ATmega4HVD/8HVD (1-FET example)
When V
VCC to increase rapidly while CREG is being charged. At the same time the digital part of the
Internal Reset
Power-on
BATT
V
INTERNAL_RESET
REG
reaches the power-on threshold V
V
CHIP STATE
BLOT, START-UP
BLOD
V
V
2.2 V
POR
V
BATT
REG
POT
CHARGER CONNECTED
Power-off
V
BLOT
CHARGER DETECTED
POT
POT
, the voltage regulator starts up. This causes
. When the voltage at V
Reset
t
TOUT
Figure 10-8 on page
REG
Active
BATT
exceeds V
8052B–AVR–09/08
42.
BATT
POT
,
Related parts for ATMEGA8HVD-4MX
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
IC AVR MCU 2.4GHZ XCEIVER 64QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ATMEGA644/AT86RF230 40-DIP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
BUNDLE ATMEGA644P/AT86RF230 QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
BUNDLE ATMEGA644P/AT86RF230 TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ATMEGA1281/AT86RF230 64-TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ATMEGA1280/AT86RF230 100TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
BUNDLE ATMEGA1280/AT86RF100-TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
BUNDLE ATMEGA2560V/AT86RF230-ZU
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ATMEGA2561/AT86RF230 64-TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet: