MC68HC705B16CFN Freescale Semiconductor, MC68HC705B16CFN Datasheet - Page 30

no-image

MC68HC705B16CFN

Manufacturer Part Number
MC68HC705B16CFN
Description
IC MCU 2.1MHZ 15K OTP 52-PLCC
Manufacturer
Freescale Semiconductor
Series
HC05r
Datasheet

Specifications of MC68HC705B16CFN

Core Processor
HC05
Core Size
8-Bit
Speed
2.1MHz
Connectivity
SCI
Peripherals
POR, WDT
Number Of I /o
32
Program Memory Size
15KB (15K x 8)
Program Memory Type
OTP
Eeprom Size
256 x 8
Ram Size
352 x 8
Voltage - Supply (vcc/vdd)
4.5 V ~ 5.5 V
Data Converters
A/D 8x8b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
52-PLCC
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MC68HC705B16CFN
Manufacturer:
MOT
Quantity:
5 510
Part Number:
MC68HC705B16CFN
Manufacturer:
MOT
Quantity:
2 132
Company:
Part Number:
MC68HC705B16CFN
Manufacturer:
MOI
Quantity:
1 000
Part Number:
MC68HC705B16CFNE
Manufacturer:
FREESCALE
Quantity:
2 512
2
2.2
The ‘load program in RAM and execute’ mode is entered if the following conditions are satisfied
when the reset pin is released to V
MC68HC805C4. The SEC bit in the options register must be inactive, i.e. set to ‘1’.
In the ‘load program in RAM and execute’ routine, user programs are loaded into MCU RAM via
the SCI port and then executed. Data is loaded sequentially, starting at RAM location $0050, until
the last byte is loaded. Program control is then transferred to the RAM program starting at location
$0051. The first byte loaded is the count of the total number of bytes in the program plus the count
byte. The program starts at the second byte in RAM. During the firmware initialization stage, the
SCI is configured for the NRZ data format (idle line, start bit, eight data bits and stop bit). The baud
rate is 9600 with a 4 MHz crystal. A program to convert ASCII S-records to the format required by
the RAM loader is available from Freescale.
If immediate execution is not desired after loading the RAM program, it is possible to hold off
execution. This is accomplished by setting the byte count to a value that is greater than the overall
length of the loaded data. When the last byte is loaded, the firmware will halt operation expecting
additional data to arrive. At this point, the reset switch is placed in the reset position which will reset
the MCU, but keep the RAM program intact. All routines can now be entered from this state,
including the one which will execute the program in RAM (see
To load a program in the EEPROM, the ‘load program in RAM and execute’ function is also used.
In this instance the process involves two distinct steps. Firstly, the RAM is loaded with a program
which will control the loading of the EEPROM, and when the RAM contents are executed, the MCU
is instructed to load the EEPROM.
The erased state of the EEPROM is $FF.
Figure 2-1
Freescale
2-2
– IRQ at 2xV
– TCAP1 at V
– PD3 at V
– PD4 at V
shows the schematic diagram of the circuit required for the serial RAM loader.
Serial RAM loader
DD
SS
MODES OF OPERATION AND PIN DESCRIPTIONS
DD
DD
for at least 30 machine cycles after reset
for at least 30 machine cycles after reset
DD
. The format used is identical to the format used for the
Section
2.3).
MC68HC05B6
Rev. 4.1

Related parts for MC68HC705B16CFN