MPC564MZP66 Freescale Semiconductor, MPC564MZP66 Datasheet - Page 1218

• Manufacturer Part Number: MPC564MZP66
• Description: IC MCU 512K FLASH 66MHZ 388-BGA
• Manufacturer: Freescale Semiconductor
• Series: MPC5xxr

Specifications of MPC564MZP66

• Core Processor: PowerPC
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: CAN, EBI/EMI, SCI, SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 56
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 2.7 V
• Data Converters: A/D 32x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 388-BGA
• For Use With: MPC564EVB - KIT EVAL FOR MPC561/562/563/564
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

Electrical Characteristics
Functional operating conditions are given in
maximum ratings are stress ratings only, and functional operation at the maximum is not guaranteed. Stress
beyond those listed may affect device reliability or cause permanent damage to the device.
This device contains circuitry protecting against damage due to high static voltage or electrical fields;
however, it is advised that normal precautions be taken to avoid application of any voltages higher than
maximum-rated voltages to this high-impedance circuit. Reliability of operation is enhanced if unused
inputs are tied to an appropriate logic voltage level (e.g., either V
F.1
The MPC561/MPC563 is available in packaged form. The package is a 388-ball PBGA having a 1.0 mm
ball pitch, Freescale case outline 1164-01 (See
F.2
F.2.1
The document referenced for the EMC testing of MPC561/MPC563 is SAE J1752/3 Issued 1995-03
F-2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
For internal digital supply of V
2.6 volt supply pins can withstand up to 3.6 volts for acumulative time of 24 hours over the lifetime of the device.
During operation the value of V
These power supplies are available on MPC563 and MPC564 only.
Maximum average current into the IRAMSTBY pin must be < 1.75mA.
V
All 2.6-V input-only pins are 5-V tolerant.
Note that long term reliability may be compromised if 2.6-V output drivers drive a node which has been previously
pulled to >3.1 V by an external component. HRESET and SRESET are fully 5-V compatible.
6.35 V on 5-V only pins (all QADC, all TPU, all QSMCM and the following MIOS pins: MDA[11:15], MDA[27:31],
MPWM16, MPIO32B[7:9]/MPWM[20:21], MPIO32B11/C_CNRX0, MPIO32B12/C_CNTX0 ). Internal structures hold
the input voltage below this maximum voltage on all of these pins, except the QSMCM RXD1/QPI1 and
RXD2/QPI2/C_CNRX0 pins, if the maximum injection current specification is met (1 mA for all pins; exception: 3 mA
on QADC pins) and VDDH is within Operating Voltage specifications (see specification 43 in
The RXD1/QGPI1 and RXD2/GPI2 pins do not have clamp diodes to VDDH. Voltage must be limited to less than 6.5
volts on these 2 pins to prevent damage.
Maximum continuous current on I/O pins provided the overall power dissipation is below the power dissipation of the
package. Proper operation is not guaranteed at this condition.
Condition applies to one pin at a time.
Transitions within the limit do not affect device reliability or cause permanent damage. Exceeding limit may cause
permanent conversion error on stressed channels and on unstressed channels.
Maximum transient current per ISO7637.
Maximum operating temperature on any solder ball in outer four rows of solder balls on the package. These rows are
referred to as “Perimeter Balls” to distinguish them from the balls in the center of the package.
Solder profile per CDF-AEC-Q100, current revision.
Moisture sensitivity per JEDEC test method J-STD-020-A (April 1999).
DDA
Package
EMI Characteristics
=5.0 V
Reference Documents
Negative current flows out of the pin and positive current flows into the pin.
±
5%.
DDL
FLASH
MPC561/MPC563 Reference Manual, Rev. 1.2
= 2.6-V typical.
must be 5.0 V
Section F.5, “DC Electrical
Figure F-64
NOTE
±
5%
and
Figure
SS
or V
F-65).
DD
Characteristics.” Absolute
).
Table
Freescale Semiconductor
F-4). Exception: