MPC564MZP66 Freescale Semiconductor, MPC564MZP66 Datasheet - Page 422

• Manufacturer Part Number: MPC564MZP66
• Description: IC MCU 512K FLASH 66MHZ 388-BGA
• Manufacturer: Freescale Semiconductor
• Series: MPC5xxr

Specifications of MPC564MZP66

• Core Processor: PowerPC
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: CAN, EBI/EMI, SCI, SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 56
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 2.7 V
• Data Converters: A/D 32x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 388-BGA
• For Use With: MPC564EVB - KIT EVAL FOR MPC561/562/563/564
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

Memory Controller
10.4
The GPCM determines the timing and value of the WE/BE signals if allowed by the port size of the
accessed bank, the transfer size of the transaction and the address accessed.
The functionality of the WE/BE[0:3] signals depends upon the value of the write enable/byte select
(WEBS) bit in the corresponding BR register. Setting WEBS to 1 will enable these signals as BE, while
clearing it to zero will enable them as WE. WE is asserted only during write access, while BE is asserted
for both read and write accesses. The timing of the WE/BE signals remains the same in either case, and is
determined by the TRLX, ACS and CSNT bits.
The upper WE/BE (WE0/BE0) indicates that the upper eight bits of the data bus (D0–D7) contains valid
data during a write/read cycle. The upper-middle write byte enable (WE1/BE1) indicates that the
upper-middle eight bits of the data bus (D8–D15) contains valid data during a write/read cycle. The
lower-middle write byte enable (WE2/BE2) indicates that the lower-middle eight bits of the data bus
(D16–D23) contains valid data during a write/read cycle. The lower write/read enable (WE3/BE3)
indicates that the lower eight bits of the data bus contains valid data during a write cycle.
The write/byte enable lines affected in a transaction for 32-bit port (PS = 00), a 16-bit port (PS = 10) and
a 8-bit port (PS = 01) are shown in
10.5
The internal Flash EEPROM (UC3F) module can be mapped to an external memory region controlled by
the memory controller. Only one region can be programmed to be dual-mapped. When dual mapping is
enabled (DME bit is set in the DMBR register) and when an internal address matches the dual-mapped
address range (as programmed in the DMBR) with the cycle type matching the AT/ATM field in
DMBR/DMOR registers, the following occurs:
10-24
1
•
•
Transfer
Word
Word
This table shows which write enables are asserted (indicated with an ‘X’) for different combinations of port size and
transfer size.
Byte
Half-
Size
The internal Flash memory does not respond to that address
The memory controller takes control of the external access
Write and Byte Enable Signals
Dual Mapping of the Internal Flash EEPROM Array
0
0
0
0
1
1
0
TSIZ
1
1
1
1
0
0
0
A30 A31
Address
0
0
1
1
0
1
0
Table 10-4. Write Enable/Byte Enable Signals Function
0
1
0
1
0
0
0
WE0/
BE0
X
X
X
MPC561/MPC563 Reference Manual, Rev. 1.2
32-bit Port Size
Table
WE1/
BE1
X
X
X
10-4.
WE2
BE2
X
X
X
WE3/
BE3
X
X
X
WE0/
BE0
X
X
X
X
X
16-bit Port Size
WE1/
BE1
X
X
X
X
X
WE2/
BE2
WE3/
BE3
1
WE0
BE0
X
X
X
X
X
X
X
/
8-bit Port Size
Freescale Semiconductor
/BE1
WE1
BE2
WE
2
WE3/
BE3