MPC564MZP66 Freescale Semiconductor, MPC564MZP66 Datasheet - Page 612

no-image

MPC564MZP66

Manufacturer Part Number
MPC564MZP66
Description
IC MCU 512K FLASH 66MHZ 388-BGA
Manufacturer
Freescale Semiconductor
Series
MPC5xxr
Datasheets

Specifications of MPC564MZP66

Core Processor
PowerPC
Core Size
32-Bit
Speed
66MHz
Connectivity
CAN, EBI/EMI, SCI, SPI, UART/USART
Peripherals
POR, PWM, WDT
Number Of I /o
56
Program Memory Size
512KB (512K x 8)
Program Memory Type
FLASH
Ram Size
32K x 8
Voltage - Supply (vcc/vdd)
2.5 V ~ 2.7 V
Data Converters
A/D 32x10b
Oscillator Type
External
Operating Temperature
-40°C ~ 125°C
Package / Case
388-BGA
For Use With
MPC564EVB - KIT EVAL FOR MPC561/562/563/564
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MPC564MZP66
Manufacturer:
FREESCALE
Quantity:
2 000
Part Number:
MPC564MZP66
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
MPC564MZP66
Manufacturer:
FREESCALE
Quantity:
2 000
Part Number:
MPC564MZP66R2
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
QADC64E Enhanced Mode Operation
The AltRef signal may be selected through the CCW as the high reference for a conversion. This allows
for the ability to “zoom” in on a portion of the convertible range with the full 10 bits. Refer to
No A/D converter can be more accurate than its analog reference. Any noise in the reference can result in
at least that much error in a conversion. The reference for the QADC64E, supplied by signals V
and V
simple capacitive bypassing may sufficed. In extreme cases, inductors or ferrite beads may be necessary
if noise or RF energy is present. Series resistance is not advisable since there is an effective DC current
requirement from the reference voltage by the internal resistor string in the RC DAC array. External
resistance may introduce error in this architecture under certain conditions. Any series devices in the filter
network should contain a minimum amount of DC resistance.
14.6.5
Analog inputs should have low AC impedance at the signals. Low AC impedance can be realized by
placing a capacitor with good high frequency characteristics at the input signal of the part. Ideally, that
capacitor should be as large as possible (within the practical range of capacitors that still have good high
frequency characteristics). This capacitor has two effects:
Series resistance can be used with the capacitor on an input signal to implement a simple RC filter. The
maximum level of filtering at the input signals is application dependent and is based on the bandpass
characteristics required to accurately track the dynamic characteristics of an input. Simple RC filtering at
the signal may be limited by the source impedance of the transducer or circuit supplying the analog signal
to be measured. Refer to
cases, the size of the capacitor at the signal may be very small.
Figure 14-50
the interaction between the external circuitry and the circuitry inside the QADC64E.
14-70
RL
It helps attenuate any noise that may exist on the input.
It sources charge during the sample period when the analog signal source is a high-impedance
source.
, should be low-pass filtered from its source to obtain a noise-free, clean signal. In many cases,
Analog Input Signals
is a simplified model of an input channel. Refer to this model in the following discussion of
Section 14.6.5.3, “Error Resulting from
MPC561/MPC563 Reference Manual, Rev. 1.2
Leakage” for more information. In some
Freescale Semiconductor
Table
RH
, AltRef,
14-19.

Related parts for MPC564MZP66