MPC564MZP66 Freescale Semiconductor, MPC564MZP66 Datasheet - Page 642

• Manufacturer Part Number: MPC564MZP66
• Description: IC MCU 512K FLASH 66MHZ 388-BGA
• Manufacturer: Freescale Semiconductor
• Series: MPC5xxr

Specifications of MPC564MZP66

• Core Processor: PowerPC
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: CAN, EBI/EMI, SCI, SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 56
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 2.7 V
• Data Converters: A/D 32x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 388-BGA
• For Use With: MPC564EVB - KIT EVAL FOR MPC561/562/563/564
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

Queued Serial Multi-Channel Module
Refer to
15.6.3
Seven pins are associated with the QSPI. When not needed by the QSPI, they can be configured for
general-purpose I/O.
determines whether the pins are designated as input or output. The user must initialize DDRQS for the
QSPI to function correctly.
15-24
Bits
4:7
0
1
2
3
The PCS0 bit represents the dual-function PCS0/SS.
1
PCS[3:0] Peripheral chip selects. Use peripheral chip-select bits to select an external device for serial data transfer. More
CONT
CONT
BITSE
Name
CONT
DSCK
MSB
DT
Section 15.6.5, “Master Mode
—
0
QSPI Pins
Continue
0 Control of chip selects returned to PORTQS after transfer is complete.
1 Peripheral chip selects remain asserted after transfer is complete.
Bits per transfer enable
0 Eight bits
1 Number of bits set in BITS field of SPCR0.
Delay after transfer
0 Delay after transfer is 17 ÷ f
1 SPCR1 DTL[7:0] specifies delay after transfer PCS valid to SCK.
PCS to SCK Delay
0 PCS valid to SCK delay is one-half SCK.
1 SPCR1 DSCKL[6:0] specifies delay from PCS valid to SCK.
than one peripheral chip select may be activated at a time, and more than one peripheral chip can be connected
to each PCS pin, provided proper fanout is observed. PCS0 shares a pin with the slave select (SS) signal, which
initiates slave mode serial transfer. If SS is taken low when the QSPI is in master mode, a mode fault occurs.
BITSE
BITSE
Command Control
—
Table 15-20
1
Figure 15-17. CR[0:F] — Command RAM 0x30 51C0, 0x30 51DF
Table 15-19. Command RAM Bit Descriptions
MPC561/MPC563 Reference Manual, Rev. 1.2
DT
DT
—
2
identifies the QSPI pins and their functions. Register DDRQS
Operation” for more information on the command RAM.
SYS
.
DSCK
DSCK
—
3
Description
PCS3
PCS3
—
4
Peripheral Chip Select
PCS2
PCS2
—
5
PCS1
PCS1
—
6
Freescale Semiconductor
PCS0
PCS0
LSB
—
7
1
1