MPC564MZP66 Freescale Semiconductor, MPC564MZP66 Datasheet - Page 890

no-image

MPC564MZP66

Manufacturer Part Number
MPC564MZP66
Description
IC MCU 512K FLASH 66MHZ 388-BGA
Manufacturer
Freescale Semiconductor
Series
MPC5xxr
Datasheets

Specifications of MPC564MZP66

Core Processor
PowerPC
Core Size
32-Bit
Speed
66MHz
Connectivity
CAN, EBI/EMI, SCI, SPI, UART/USART
Peripherals
POR, PWM, WDT
Number Of I /o
56
Program Memory Size
512KB (512K x 8)
Program Memory Type
FLASH
Ram Size
32K x 8
Voltage - Supply (vcc/vdd)
2.5 V ~ 2.7 V
Data Converters
A/D 32x10b
Oscillator Type
External
Operating Temperature
-40°C ~ 125°C
Package / Case
388-BGA
For Use With
MPC564EVB - KIT EVAL FOR MPC561/562/563/564
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MPC564MZP66
Manufacturer:
FREESCALE
Quantity:
2 000
Part Number:
MPC564MZP66
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
MPC564MZP66
Manufacturer:
FREESCALE
Quantity:
2 000
Part Number:
MPC564MZP66R2
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
CDR3 Flash (UC3F) EEPROM
21.3.8.2
The shadow information words are erased with either the lowest numbered block or small block 0,
depending on the array configuration and the state of SBEN[0]. If the lowest numbered block in the array
does not host a small block, then the shadow information words are erased with the lowest numbered
block. If the lowest numbered block hosts a small block, then the shadow information words may get
erased with small block 0. If SBEN[0] = 0 for this array configuration, then the shadow information words
get erased with the lowest numbered block. If SBEN[0] = 1 for this same array configuration, then the
shadow information words get erased with small block 0 only.
21.3.8.3
The erase operation may be suspended to allow read accesses to the array. Setting the HSUS bit in the
UC3FCTL to a 1 while EHV=1 and HVS=1 forces the array into an erase suspend state. The deassertion
of the HVS bit (HVS = 0) signifies that the erase operation has been successfully suspended. The HVS bit
should negate within 10 ms of asserting the HSUS bit.
While in erase suspend mode, normal read accesses may be performed to the UC3F array or shadow
information words. Reads to the array block or blocks targeted for erase return indeterminate data since
only a partial erase operation has been performed.
The erase operation may be resumed by setting HSUS = 0.
21.3.9
The UC3F EEPROM goes into a low power operation, or stop operation, while STOP = 1. When the STOP
bit is set, only the control registers can be accessed on the UC3F EEPROM module. The UC3F EEPROM
array may not be programmed, erased or read while STOP = 1.
21-28
State
S5
Stop Operation
Erase Suspend Operation:
The erase operation is suspended to either read
the array or disable the module. Once HVS reads
as a 0, the erase operation is suspended. Normal
reads to the array can be performed if the module
is enabled; read accesses to locations in blocks
being erased return indeterminate data.
Erasing Shadow Information Words
Erase Suspend
Repeated suspending of an erase operation to fetch array contents may
severely extend the erase operation. The internal erase hardware may only
resume the erase operation at predefined steps of the internal erase hardware
sequence; interrupting the erase operation on a high frequency basis may
cause the internal erase hardware to delay completion of the current step and
delay advancement to the next step of the internal erase hardware sequence.
Table 21-8. Erase Interlock State Descriptions (continued)
Mode
MPC561/MPC563 Reference Manual, Rev. 1.2
NOTE
State
Next
S1
S4
T10
T9
Reset.
Write HSUS = 0 or re-enable the
UC3F module.
Transition Requirement
Freescale Semiconductor

Related parts for MPC564MZP66