C8051F320 Silicon Laboratories Inc, C8051F320 Datasheet - Page 155

• Manufacturer Part Number: C8051F320
• Description: IC 8051 MCU 16K FLASH 32LQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F32xr

Specifications of C8051F320

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 25
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 17x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

Bit7:
Bits6-5:
Bit4:
Bit3:
Bit2:
Bit1:
Bit0:
ISOUD
R/W
Bit7
ISOUD: ISO Update
This bit affects all IN Isochronous endpoints.
0: When software writes INPRDY = ‘1’, USB0 will send the packet when the next IN token is
received.
1: When software writes INPRDY = ‘1’, USB0 will wait for a SOF token before sending the packet.
If an IN token is received before a SOF token, USB0 will send a zero-length data packet.
Unused. Read = 00b. Write = don’t care.
USBINH: USB0 Inhibit
This bit is set to ‘1’ following a power-on reset (POR) or an asynchronous USB0 reset (see Bit3:
RESET). Software should clear this bit after all USB0 and transceiver initialization is complete. Soft-
ware cannot set this bit to ‘1’.
0: USB0 enabled.
1: USB0 inhibited. All USB traffic is ignored.
USBRST: Reset Detect
Writing ‘1’ to this bit forces an asynchronous USB0 reset. Reading this bit provides bus reset status
information.
Read:
0: Reset signaling is not present on the bus.
1: Reset signaling detected on the bus.
RESUME: Force Resume
Software can force resume signaling on the bus to wake USB0 from suspend mode. Writing a ‘1’ to
this bit while in Suspend mode (SUSMD = ‘1’) forces USB0 to generate Resume signaling on the bus
(a remote Wakeup event). Software should write RESUME = ‘0’ after 10 ms to15 ms to end the
Resume signaling. An interrupt is generated, and hardware clears SUSMD, when software writes
RESUME = ‘0’.
SUSMD: Suspend Mode
Set to ‘1’ by hardware when USB0 enters suspend mode. Cleared by hardware when software writes
RESUME = ‘0’ (following a remote wakeup) or reads the CMINT register after detection of Resume
signaling on the bus.
0: USB0 not in suspend mode.
1: USB0 in suspend mode.
SUSEN: Suspend Detection Enable
0: Suspend detection disabled. USB0 will ignore suspend signaling on the bus.
1: Suspend detection enabled. USB0 will enter suspend mode if it detects suspend signaling on the
bus.
R/W
Bit6
-
Figure 15.11. POWER: USB0 Power (USB Register)
R/W
Bit5
-
USBINH
R/W
Bit4
USBRST
R/W
Bit3
Rev. 1.1
RESUME
R/W
Bit2
SUSMD
Bit1
R
C8051F320/1
SUSEN
R/W
Bit0
USB Address:
00010000
Reset Value
0x01
155