C8051F320 Silicon Laboratories Inc, C8051F320 Datasheet - Page 217

• Manufacturer Part Number: C8051F320
• Description: IC 8051 MCU 16K FLASH 32LQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F32xr

Specifications of C8051F320

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 25
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 17x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

19.
Each MCU includes four counter/timers: two are 16-bit counter/timers compatible with those found in the standard
8051, and two are 16-bit auto-reload timer for use with the ADC, SMBus, USB (frame measurements), or for general
purpose use. These timers can be used to measure time intervals, count external events and generate periodic interrupt
requests. Timer 0 and Timer 1 are nearly identical and have four primary modes of operation. Timer 2 and Timer 3
offer 16-bit and split 8-bit timer functionality with auto-reload.
Timers 0 and 1 may be clocked by one of five sources, determined by the Timer Mode Select bits (T1M-T0M) and
the Clock Scale bits (SCA1-SCA0). The Clock Scale bits define a pre-scaled clock from which Timer 0 and/or
Timer 1 may be clocked (See Figure 19.6 for pre-scaled clock selection).
Timer 0/1 may then be configured to use this pre-scaled clock signal or the system clock. Timer 2 and Timer 3 may be
clocked by the system clock, the system clock divided by 12, or the external oscillator clock source divided by 8.
Timer 0 and Timer 1 may also be operated as counters. When functioning as a counter, a counter/timer register is
incremented on each high-to-low transition at the selected input pin (T0 or T1). Events with a frequency of up to one-
fourth the system clock's frequency can be counted. The input signal need not be periodic, but it should be held at a
given level for at least two full system clock cycles to ensure the level is properly sampled.
19.1. Timer 0 and Timer 1
Each timer is implemented as a 16-bit register accessed as two separate bytes: a low byte (TL0 or TL1) and a high
byte (TH0 or TH1). The Counter/Timer Control register (TCON) is used to enable Timer 0 and Timer 1 as well as
indicate status. Timer 0 interrupts can be enabled by setting the ET0 bit in the IE register
Register Descriptions” on page
tion
T0M0 in the Counter/Timer Mode register (TMOD). Each timer can be configured independently. Each operating
mode is described below.
19.1.1. Mode 0: 13-bit Counter/Timer
Timer 0 and Timer 1 operate as 13-bit counter/timers in Mode 0. The following describes the configuration and oper-
ation of Timer 0. However, both timers operate identically, and Timer 1 is configured in the same manner as
described for Timer 0.
The TH0 register holds the eight MSBs of the 13-bit counter/timer. TL0 holds the five LSBs in bit positions TL0.4-
TL0.0. The three upper bits of TL0 (TL0.7-TL0.5) are indeterminate and should be masked out or ignored when read-
ing. As the 13-bit timer register increments and overflows from 0x1FFF (all ones) to 0x0000, the timer overflow flag
TF0 (TCON.5) is set and an interrupt will occur if Timer 0 interrupts are enabled.
The C/T0 bit (TMOD.2) selects the counter/timer's clock source. When C/T0 is set to logic 1, high-to-low transitions
at the selected Timer 0 input pin (T0) increment the timer register (Refer to
Decoder” on page 129
clock defined by the T0M bit (CKCON.3). When T0M is set, Timer 0 is clocked by the system clock. When T0M is
cleared, Timer 0 is clocked by the source selected by the Clock Scale bits in CKCON (see Figure 19.6).
Timer 0 and Timer 1 Modes:
8-bit counter/timer with auto-reload
Two 8-bit counter/timers (Timer 0
8.3.5). Both counter/timers operate in one of four primary modes selected by setting the Mode Select bits T1M1-
TIMERS
13-bit counter/timer
16-bit counter/timer
only)
for information on selecting and configuring external I/O pins). Clearing C/T selects the
61); Timer 1 interrupts can be enabled by setting the ET1 bit in the IE register
Timer 2 Modes:
Two 8-bit timers with auto-reload
16-bit timer with auto-reload
Rev. 1.1
Timer 3 Modes:
Two 8-bit timers with auto-reload
Section “14.1. Priority Crossbar
16-bit timer with auto-reload
C8051F320/1
(Section “8.3.5. Interrupt
(Sec-
217