C8051F330 Silicon Laboratories Inc, C8051F330 Datasheet - Page 140
![no-image](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_sml.jpg)
C8051F330
Manufacturer Part Number
C8051F330
Description
IC 8051 MCU 8K FLASH 20MLP
Manufacturer
Silicon Laboratories Inc
Series
C8051F33xr
Datasheet
1.C8051F330R.pdf
(208 pages)
Specifications of C8051F330
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
POR, PWM, Temp Sensor, WDT
Number Of I /o
17
Program Memory Size
8KB (8K x 8)
Program Memory Type
FLASH
Ram Size
768 x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 3.6 V
Data Converters
A/D 16x10b; D/A 1x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
20-QFN
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051F330
Manufacturer:
SILICON
Quantity:
359
Part Number:
C8051F330
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
Company:
Part Number:
C8051F330-GM
Manufacturer:
SiliconL
Quantity:
6 420
Company:
Part Number:
C8051F330-GM
Manufacturer:
SILICON
Quantity:
121
Part Number:
C8051F330-GM
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
Company:
Part Number:
C8051F330-GM-15T
Manufacturer:
SILICON
Quantity:
3 741
Part Number:
C8051F330-GMR
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
Company:
Part Number:
C8051F330GM
Manufacturer:
SILLAB
Quantity:
4 419
C8051F330/1, C8051F330D
15.5.4. Slave Transmitter Mode
Serial data is transmitted on SDA and the clock is received on SCL. When slave events are enabled (INH
= 0), the interface enters Slave Receiver Mode (to receive the slave address) when a START followed by a
slave address and direction bit (READ in this case) is received. Upon entering Slave Transmitter Mode, an
interrupt is generated and the ACKRQ bit is set. Software responds to the received slave address with an
ACK, or ignores the received slave address with a NACK. If the received slave address is ignored, slave
interrupts will be inhibited until a START is detected. If the received slave address is acknowledged, data
should be written to SMB0DAT to be transmitted. The interface enters Slave Transmitter Mode, and trans-
mits one or more bytes of data. After each byte is transmitted, the master sends an acknowledge bit; if the
acknowledge bit is an ACK, SMB0DAT should be written with the next data byte. If the acknowledge bit is
a NACK, SMB0DAT should not be written to before SI is cleared (Note: an error condition may be gener-
ated if SMB0DAT is written following a received NACK while in Slave Transmitter Mode). The interface
exits Slave Transmitter Mode after receiving a STOP. Note that the interface will switch to Slave Receiver
Mode if SMB0DAT is not written following a Slave Transmitter interrupt. Figure 15.11 shows a typical Slave
Transmitter sequence. Two transmitted data bytes are shown, though any number of bytes may be trans-
mitted. Notice that the ‘data byte transferred’ interrupts occur after the ACK cycle in this mode.
140
S
Received by SMBus
Interface
Transmitted by
SMBus Interface
SLA
Figure 15.11. Typical Slave Transmitter Sequence
Interrupt
R
A
Data Byte
Rev. 1.2
Interrupt
A
S = START
P = STOP
N = NACK
R = READ
SLA = Slave Address
Data Byte
Interrupt
N
Interrupt
P