MC908AZ32ACFU Freescale Semiconductor, MC908AZ32ACFU Datasheet - Page 106

no-image

MC908AZ32ACFU

Manufacturer Part Number
MC908AZ32ACFU
Description
IC MCU 32K FLASH 8.4MHZ 64-QFP
Manufacturer
Freescale Semiconductor
Series
HC08r
Datasheet

Specifications of MC908AZ32ACFU

Core Processor
HC08
Core Size
8-Bit
Speed
8MHz
Connectivity
CAN, SCI, SPI
Peripherals
LVD, POR, PWM
Number Of I /o
40
Program Memory Size
32KB (32K x 8)
Program Memory Type
FLASH
Eeprom Size
512 x 8
Ram Size
1K x 8
Voltage - Supply (vcc/vdd)
4.5 V ~ 5.5 V
Data Converters
A/D 15x8b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
64-QFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MC908AZ32ACFU
Manufacturer:
FREESCALE
Quantity:
3
Part Number:
MC908AZ32ACFU
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
MC908AZ32ACFU
Manufacturer:
MOTOROLA/摩托罗拉
Quantity:
20 000
Part Number:
MC908AZ32ACFUE
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
MC908AZ32ACFUE
Manufacturer:
FREESCALE
Quantity:
20 000
Part Number:
MC908AZ32ACFUER
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Clock Generator Module (CGM)
8.9.4 Reaction Time Calculation
The actual acquisition and lock times can be calculated using the equations below. These equations yield
nominal values under the following conditions:
The K factor in the equations is derived from internal PLL parameters. K
is configured in acquisition mode, and K
(See
Note the inverse proportionality between the lock time and the reference frequency.
In automatic bandwidth control mode, the acquisition and lock times are quantized into units based on the
reference frequency. (See
clock cycles, n
before exiting acquisition mode. A certain number of clock cycles, n
PLL is within the lock mode entry tolerance, Δ
multiple of n
Also, since the average frequency over the entire measurement period must be within the specified
tolerance, the total time usually is longer than t
In manual mode, it is usually necessary to wait considerably longer than t
clock (see
Influences on Reaction
When defining a limit in software for the maximum lock time, the value must allow for variation due to all
of the factors mentioned in this section, especially due to the C
influences.
The calculated lock time is only an indication and it is the customer’s responsibility to allow enough of a
guard band for their application. Prior to finalizing any software and while determining the maximum lock
time, take into account all device to device differences. Typically, applications set the maximum lock time
as an order of magnitude higher than the measured value. This is considered sufficient for all such device
to device variation.
Freescale recommends measuring the lock time of the application system by utilizing dedicated software,
running in FLASH, EEPROM or RAM. This should toggle a port pin when the PLL is first configured and
switched on, then again when it goes from acquisition to lock mode and finally again when the PLL lock
106
8.3.2.2 Acquisition and Tracking
Correct selection of filter capacitor, C
Room temperature operation
Negligible external leakage on CGMXFC
Negligible noise
8.3.3 Base Clock Selector
ACQ
ACQ
/f
CGMRDV
, is required to ascertain that the PLL is within the tracking mode entry tolerance, Δ
Time, may slow the lock time considerably.
, and the acquisition to lock time, t
8.3.2.3 Manual and Automatic PLL Bandwidth
MC68HC908AZ32A Data Sheet, Rev. 2
Circuit), because the factors described in
Modes).
t
acq
t
trk
al
is the K factor when the PLL is configured in tracking mode.
t
=
=
Lock
F
(see
Lock
Lock
------------------- -
f
------------------- -
f
CGMRDV
CGMRDV
=
V
. Therefore, the acquisition time, t
V
8.9.3 Choosing a Filter
as calculated above.
DDA
DDA
t
ACQ
+
AL
----------- -
K
------------ -
K
t
AL
, is an integer multiple of n
TRK
4
ACQ
F
8
capacitor and application specific
TRK
, is required to ascertain that the
acq
Lock
Modes). A certain number of
Capacitor).
is the K factor when the PLL
before selecting the PLL
8.9.2 Parametric
Freescale Semiconductor
ACQ
, is an integer
TRK
/f
CGMRDV
TRK
.
,

Related parts for MC908AZ32ACFU