EE80C196KB16 Intel, EE80C196KB16 Datasheet
EE80C196KB16
Specifications of EE80C196KB16
Available stocks
Related parts for EE80C196KB16
EE80C196KB16 Summary of contents
Page 1
... Information in this document is provided in connection with Intel products Intel assumes no liability whatsoever including infringement of any patent or copyright for sale and use of Intel products except as provided in Intel’s Terms and Conditions of Sale for such products Intel retains the right to make changes to these specifications at any time without notice Microcomputer Products may have minor variations to this specification known as errata ...
Page 2
Figure 1 8XC196KB Block Diagram 2 270909 – 1 ...
Page 3
... C W All thermal impedance data is approximate for static air conditions power dissipation Values will change depending on operation conditions and application See the Intel Packaging Handbook (order number 240800) for a description of Intel’s thermal impedance test methodology Table 2 8XC196KB Memory Map Description External Memory ...
Page 4
Figure 3 68-Pin Package (PLCC Top View) NOTE The above pin out diagram applies to the OTP (87C196KB) device The OTP device uses all of the programming pins shown above The ROM (83C196KB) device only uses programming pins ...
Page 5
NOTE N C means No Connect (do not connect these pins) NOTE The above pin out diagram applies to the OTP (87C196KB) device The OTP device uses all of the programming pins shown above The ROM (83C196KB) device only uses ...
Page 6
PIN DESCRIPTIONS Symbol V Main supply voltage (5V Digital circuit ground (0V) There are multiple Reference voltage for the A D converter (5V) V REF portion of the A D converter and the ...
Page 7
PIN DESCRIPTIONS (Continued) Symbol Port 0 8-bit high impedance input-only port Three pins can be used as digital inputs and or as analog inputs to the on-chip A D converter Port 1 8-bit quasi-bidirectional I O port These pins are ...
Page 8
... NOTICE This data sheet contains preliminary infor- mation on new products in production The specifica- tions are subject to change without notice Verify with your local Intel Sales office that you have the latest data sheet before finalizing a design 125 C a WARNING Stressing the device beyond the ‘‘Absolute ...
Page 9
DC CHARACTERISTICS (Continued) Symbol Description I Logical 0 Input Current in Reset IL1 BHE Logical 0 Input Current in Reset IL2 ALE RD INST I Logical 1 Input Current IH1 on NMI Pin Hyst Hysteresis on ...
Page 10
AC CHARACTERISTICS Test Conditions Capacitive load on all pins The system must meet these specifications to work with the 87C196KB Symbol Description T Address Valid to READY Setup AVYV T NonREADY Time YLYH T READY Hold after CLKOUT ...
Page 11
AC CHARACTERISTICS (Continued) Test Conditions Capacitive load on all pins The 87C196KB will meet these specifications Symbol Description F Frequency on XTAL1 12 MHz XTAL F Frequency on XTAL1 16 MHz XTAL MHz OSC XTAL T ...
Page 12
System Bus Timings 12 270909 – 6 ...
Page 13
READY Timings (One Wait State) Buswidth Bus Timings 8XC196KB 8XC196KB16 270909 – 7 270909 – ...
Page 14
HOLD HLDA Timings Symbol Description T HOLD Setup HVCH T CLKOUT Low to HLDA Low CLHAL T CLKOUT Low to BREQ Low CLBRL T HLDA Low to Address Float HALAZ T HLDA Low to BHE INST RD WR ...
Page 15
EXTERNAL CLOCK DRIVE Symbol Parameter 1 T Oscillator Frequency 12 MHz XLXL 1 T Oscillator Frequency 16 MHz XLXL T Oscillator Period 12 MHz XLXL T Oscillator Period 16 MHz XLXL T High Time XHXX T Low Time XLXX T ...
Page 16
EXPLANATION OF AC SYMBOLS Each symbol is two pairs of letters prefixed by ‘‘T’’ for time The characters in a pair indicate a signal and its condition respectively Symbols represent the time between the two signal condition points ...
Page 17
A D CHARACTERISTICS At a clock speed of 6 MHz or less the clock prescal- er should be disabled This is accomplished by set- ting IOC2 higher frequencies (greater than 6 MHz) the clock prescaler ...
Page 18
OTPROM SPECIFICATIONS OTPROM PROGRAMMING OPERATING CONDITIONS Symbol T Ambient Temperature During Programming A ( Supply Voltages During Programming CC PD REF V Programming Mode Supply Voltage EA V EPROM Programming Supply Voltage PP (3) V ...
Page 19
DC OTPROM PROGRAMMING CHARACTERISTICS Symbol Description I V Supply Current (When Programming NOTE Do not apply V until V is stable and within specifications and the oscillator clock has stabilized or the device may damaged ...
Page 20
SLAVE PROGRAMMING MODE TIMING IN DATA PROGRAM MODE WITH REPEATED PROG PULSE AND AUTO INCREMENT 20 270909 –17 ...
Page 21
... Data sheets are changed as new device information becomes available Verify with your local Intel sales office that you have the latest version before finalizing a design or ordering devic- es ...
Page 22
The following differences exist between (-003) and version (-002) 1 The 12 MHz and 16 MHz devices were com- bined in this data sheet The 87C196KB 12 MHz only data sheet (272035-001) is now obsolete 2 Changes were ...