OP97FPZ Analog Devices Inc, OP97FPZ Datasheet - Page 5

• Manufacturer Part Number: OP97FPZ
• Description: IC OPAMP GP LP PREC 8DIP
• Manufacturer: Analog Devices Inc
• Type: General Purpose Amplifierr

Specifications of OP97FPZ

• Slew Rate: 0.2 V/µs
• Amplifier Type: General Purpose
• Number Of Circuits: 1
• -3db Bandwidth: 900kHz
• Current - Input Bias: 30pA
• Voltage - Input Offset: 30µV
• Current - Supply: 380µA
• Voltage - Supply, Single/dual (±): ±2 V ~ 20 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Through Hole
• Package / Case: 8-DIP (0.300", 7.62mm)
• Op Amp Type: Low Power
• No. Of Amplifiers: 1
• Bandwidth: 900kHz
• Supply Voltage Range: ± 2V To ± 20V
• Amplifier Case Style: DIP
• No. Of Pins: 8
• Common Mode Rejection Ratio: 132
• Current, Input Bias: ±30 pA
• Current, Input Offset: 30 pA
• Current, Supply: 380 μA
• Impedance, Thermal: 43 °C/W
• Package Type: PDIP-8
• Resistance, Input: 30 Megohms
• Temperature, Operating, Range: -40 to +85 °C
• Voltage, Gain: 2000 V/mV
• Voltage, Input: ±20 V
• Voltage, Noise: 17 nV/sqrt Hz
• Voltage, Offset: 30 μV
• Voltage, Output, High: +14 V
• Voltage, Output, Low: -14 V
• Voltage, Supply: ±15 V
• Rail/rail I/o Type: No
• Number Of Elements: 1
• Input Offset Voltage: 75uV
• Input Bias Current: 150pA
• Single Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (typ): ±15V
• Voltage Gain In Db: 126.02dB
• Power Supply Rejection Ratio: 110dB
• Power Supply Requirement: Dual
• Shut Down Feature: No
• Single Supply Voltage (min): Not RequiredV
• Single Supply Voltage (max): Not RequiredV
• Dual Supply Voltage (min): ±2V
• Dual Supply Voltage (max): ±20V
• Technology: Bipolar
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Through Hole
• Pin Count: 8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Output Type: -
• Current - Output / Channel: -
• Gain Bandwidth Product: -
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

ABSOLUTE MAXIMUM RATINGS
Absolute maximum ratings apply to both DICE and packaged
parts, unless otherwise noted.
Table 3.
Parameter
Supply Voltage
Input Voltage
Differential Input Voltage
Differential Input Current
Output Short-Circuit Duration
Operating Temperature Range
OP97E, OP97F (P, S)
Storage Temperature Range
Junction Temperature Range
Lead Temperature (Soldering, 60 sec)
1
2
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
For supply voltages less than ±20 V, the absolute maximum input voltage is
The inputs of the OP97 are protected by back-to-back diodes. Current-
equal to the supply voltage.
limiting resistors are not used in order to achieve low noise. Differential
input voltages greater than 1 V cause excessive current to flow through the
input protection diodes unless limiting resistance is used.
1
2
2
±20 V
Indefinite
Rating
±20 V
±1 V
±10 mA
−40°C to +85°C
−65°C to +150°C
−65°C to +150°C
300°C
Rev. G | Page 5 of 16
THERMAL RESISTANCE
θ
soldered in a circuit board for surface-mount packages.
Table 4
Package Type
8-Lead PDIP (P Suffix)
8-Lead SOIC (S Suffix)
1
ESD CAUTION
θ
device in socket for PDIP package; θ
printed circuit board for SOIC package.
JA
JA
is specified for the worst-case conditions, that is, a device
is specified for worst-case mounting conditions, that is, θ
.
JA
θ
103
158
is specified for device soldered to
JA
1
θ
43
43
JC
JA
is specified for
Unit
°C/W
°C/W
OP97