LT6234IS8 Linear Technology, LT6234IS8 Datasheet - Page 18
![IC OP AMP DUAL 60MHZ R-R 8-SOIC](/photos/6/62/66297/8-soic_05-08-1610_sml.jpg)
LT6234IS8
Manufacturer Part Number
LT6234IS8
Description
IC OP AMP DUAL 60MHZ R-R 8-SOIC
Manufacturer
Linear Technology
Datasheet
1.LT6233CS6-10TRMPBF.pdf
(24 pages)
Specifications of LT6234IS8
Amplifier Type
General Purpose
Number Of Circuits
2
Output Type
Rail-to-Rail
Slew Rate
17 V/µs
Gain Bandwidth Product
60MHz
Current - Input Bias
1.5µA
Voltage - Input Offset
50µV
Current - Supply
1.15mA
Current - Output / Channel
55mA
Voltage - Supply, Single/dual (±)
3 V ~ 12.6 V, ±1.5 V ~ 6.3 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
-3db Bandwidth
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LT6234IS8
Manufacturer:
LT
Quantity:
10 000
Part Number:
LT6234IS8
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LT6234IS8#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LT6234IS8#TRPBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
LT6233/LT6233-10
LT6234/LT6235
applicaTions inForMaTion
With the amplifier connected in a gain of A
can invert with very heavy overdrive. To avoid this inver-
sion, limit the input overdrive to 0.5V beyond the power
supply rails.
ESD
The LT6233/LT6234/LT6235 have reverse-biased ESD
protection diodes on all inputs and outputs as shown in
Figure 1. If these pins are forced beyond either supply,
unlimited current will flow through these diodes. If the
current is transient and limited to one hundred milliamps
or less, no damage to the device will occur.
Noise
The noise voltage of the LT6233/LT6234/LT6235 is
equivalent to that of a 225Ω resistor, and for the lowest
possible noise it is desirable to keep the source and feed-
back resistance at or below this value, i.e., R
≤ 225Ω. With R
amplifier is:
Below this resistance value, the amplifier dominates the
noise, but in the region between 225Ω and about 30k,
the noise is dominated by the resistor thermal noise. As
the total resistance is further increased beyond 30k, the
amplifier noise current multiplied by the total resistance
eventually dominates the noise.
18
e
N
= √(1.9nV)
S
2
+ R
+ (1.9nV)
G
||R
FB
2
= 225Ω the total noise of the
= 2.69nV/√Hz
V
≥ 2, the output
S
+ R
G
||R
FB
The product of e
gauge low noise amplifiers. Most low noise amplifiers
with low e
require low noise voltage with the lowest possible supply
current, this product can prove to be enlightening. The
LT6233/LT6234/LT6235 have an e
only 2.1 per amplifier, yet it is common to see amplifiers
with similar noise specifications to have e
high as 13.5.
For a complete discussion of amplifier noise, see the
LT1028 data sheet.
Enable Pin
The LT6233 and LT6233-10 include an ENABLE pin that
shuts down the amplifier to 10µA maximum supply cur-
rent. The ENABLE pin must be driven low to operate the
amplifier with normal supply current. The ENABLE pin
must be driven high to within 0.35V of V
the supply current. This can be accomplished with simple
gate logic; however care must be taken if the logic and the
LT6233 operate from different supplies. If this is the case,
then open-drain logic can be used with a pull-up resis-
tor to ensure that the amplifier remains off. See Typical
Performance Characteristics.
The output leakage current when disabled is very low;
however, current can flow into the input protection diodes
D1 and D2 if the output voltage exceeds the input voltage
by a diode drop.
N
have high I
N
• √I
SUPPLY
SUPPLY
current. In applications that
is an interesting way to
N
• √I
SUPPLY
+
N
to shut down
• √I
product of
SUPPLY
623345fc
as