LT6234IDD#TRPBF Linear Technology, LT6234IDD#TRPBF Datasheet - Page 9

• Manufacturer Part Number: LT6234IDD#TRPBF
• Description: IC OP AMP DUAL 60MHZ R-R 8-DFN
• Manufacturer: Linear Technology

Specifications of LT6234IDD#TRPBF

• Amplifier Type: General Purpose
• Number Of Circuits: 2
• Output Type: Rail-to-Rail
• Slew Rate: 17 V/µs
• Gain Bandwidth Product: 60MHz
• Current - Input Bias: 1.5µA
• Voltage - Input Offset: 75µV
• Current - Supply: 1.15mA
• Current - Output / Channel: 55mA
• Voltage - Supply, Single/dual (±): 3 V ~ 12.6 V, ±1.5 V ~ 6.3 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-DFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• -3db Bandwidth: -

elecTrical characTerisTics
temperature range. V
SYMBOL
V
V
I
I
A
V
CMRR
PSRR
V
V
I
I
I
V
V
t
t
SR
FPBW
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: Inputs are protected by back-to-back diodes. If the differential
input voltage exceeds 0.7V, the input current must be limited to less than
40mA.
Note 3: A heat sink may be required to keep the junction temperature
below the absolute maximum rating when the output is shorted
indefinitely.
Note 4: The LT6233C/LT6233I the LT6234C/LT6234I, and LT6235C/LT6235I
are guaranteed functional over the temperature range of –40°C to 85°C.
B
OS
SC
S
ENABLE
ON
OFF
OS
OS
VOL
CM
OL
OH
L
H
TC
PARAMETER
Input Offset Voltage
Input Offset Voltage Match
(Channel-to-Channel) (Note 6)
Input Offset Voltage Drift (Note 10)
Input Bias Current
I
Input Offset Current
Large-Signal Gain
Input Voltage Range
Common Mode Rejection Ratio
CMRR Match (Channel-to-Channel) (Note 6) V
Power Supply Rejection Ratio
PSRR Match (Channel-to-Channel) (Note 6)
Output Voltage Swing Low (Note 8)
Output Voltage Swing High (Note 8)
Short-Circuit Current
Supply Current per Amplifier
Disabled Supply Current per Amplifier
ENABLE Pin Current
ENABLE Pin Input Voltage Low
ENABLE Pin Input Voltage High
Output Leakage Current
Turn-On Time
Turn-Off Time
Slew Rate
Full-Power Bandwidth (Note 9)
B
Match (Channel-to-Channel) (Note 6)
S
= ±5V, V
CM
= V
OUT
= 0V, ENABLE = 0V, unless otherwise noted. (Note 5)
CONDITIONS
LT6233IS6, LT6233IS6-10
LT6234IS8, LT6235IGN
LT6234IDD
V
V
Guaranteed by CMRR
V
V
V
No Load
I
I
No Load
I
I
ENABLE = 4.8V
ENABLE = 0.3V
ENABLE = 4.8V, V
ENABLE = 5V to 0V, R
ENABLE = 0V to 5V, R
A
LT6233-10, A
V
SINK
SINK
SOURCE
SOURCE
O
O
CM
CM
S
S
V
OUT
= ±1.5V to ±5V
= ±1.5V to ±5V
= –1, R
= ±4.5V, R
= ±4.5V, R
= –3V to 4V
= –3V to 4V
= 5mA
= 15mA
= 3V
The
= 5mA
= 15mA
P-P
L
= 1k, V
l
; LT6233I, LT6234I, LT6235I
L
L
V
denotes the specifications which apply over the –40°C < T
= 10k
= 1k
= –10, R
O
O
= ±1V
Note 5: The LT6233C/LT6234C/LT6235C are guaranteed to meet specified
performance from 0°C to 70°C. The LT6233C/LT6234C/LT6235C are
designed, characterized and expected to meet specified performance from
–40°C to 85°C, but are not tested or QA sampled at these temperatures.
The LT6233I/LT6234I/LT6235I are guaranteed to meet specified
performance from –40°C to 85°C.
Note 6: Matching parameters are the difference between the two amplifiers
A and D and between B and C of the LT6235; between the two amplifiers
of the LT6234. CMRR and PSRR match are defined as follows: CMRR and
PSRR are measured in µV/V on the matched amplifiers. The difference is
calculated between the matching sides in µV/V. The result is converted to
dB.
= –2V to 2V
L
L
= 1k
= 1k
L
= 1k, V
O
= –2V to 2V
LT6233/LT6233-10
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
1.06
MIN
±30
LT6234/LT6235
4.8
68
20
–3
90
84
90
84
10
TYP
900
160
0.5
95
1
1
1000
–110
MAX
1.75
700
550
650
195
370
210
445
0.4
0.5
0.3
50
70
3
4
4
A
< 85°C
623345fc
UNITS
µV/°C
V/mV
V/mV
9
V/µs
V/µs
MHz
mV
mV
mV
mV
mV
mV
mA
mA
µV
µV
µV
µV
µA
µA
µA
dB
dB
dB
dB
µA
µA
µA
ns
µs
V
V
V