EL5177IY Intersil, EL5177IY Datasheet - Page 9

IC DRVR DIFF 550MHZ TP 10-MSOP

EL5177IY

Manufacturer Part Number
EL5177IY
Description
IC DRVR DIFF 550MHZ TP 10-MSOP
Manufacturer
Intersil
Datasheet

Specifications of EL5177IY

Amplifier Type
Differential
Number Of Circuits
1
Output Type
Differential
Slew Rate
1100 V/µs
Gain Bandwidth Product
200MHz
-3db Bandwidth
550MHz
Current - Input Bias
14µA
Voltage - Input Offset
1400µV
Current - Supply
12.5mA
Current - Output / Channel
50mA
Voltage - Supply, Single/dual (±)
4.75 V ~ 11 V, ±2.38 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
10-MSOP, Micro10™, 10-uMAX, 10-uSOP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
EL5177IY
Manufacturer:
Intersil
Quantity:
200
Part Number:
EL5177IYZ
Manufacturer:
Intersil
Quantity:
500
The bandwidth of the EL5177 depends on the load and the
feedback network. R
load for gains other than +1. As this combination gets
smaller, the bandwidth falls off. Consequently, R
minimum value that should not be exceeded for optimum
bandwidth performance. For gain of +1, R
For the gains other than +1, optimum response is obtained
with R
The EL5177 has a gain bandwidth product of 200MHz for
R
Equation 2:
Driving Capacitive Loads and Cables
The EL5177 can drive a 23pF differential capacitor in parallel
with a 1kΩ differential load with less than 5dB of peaking at
gain of +1. If less peaking is desired in applications, a small
series resistor (usually between 5Ω to 50Ω) can be placed in
series with each output to eliminate most peaking. However,
this will reduce the gain slightly. If the gain setting is greater
than 1, the gain resistor R
for any gain loss which may be created by the additional
series resistor at the output.
When used as a cable driver, double termination is always
recommended for reflection-free performance. For those
applications, a back-termination series resistor at the
amplifier's output will isolate the amplifier from the cable and
allow extensive capacitive drive. However, other applications
may have high capacitive loads without a back-termination
resistor. Again, a small series resistor at the output can help
to reduce peaking.
Disable/Power-Down
The EL5177 can be disabled and its outputs placed in a high
impedance state. The turn-off time is about 1.2µs and the
turn-on time is about 130ns. When disabled, the amplifier's
supply current is reduced to 1.7µA for I
typically, thereby effectively eliminating the power
consumption. The amplifier's power-down can be controlled
by standard CMOS signal levels at the EN pin. The applied
logic signal is relative to V
applying a signal that is less than 1.5V below V
the amplifier. The amplifier will be disabled when the signal
at the EN pin is above V
Output Drive Capability
The EL5177 has internal short circuit protection. Its typical
short circuit current is ±40mA. If the output is shorted
indefinitely, the power dissipation could easily increase such
that the part will be destroyed. Maximum reliability is
maintained if the output current never exceeds ±40mA. This
limit is set by the design of the internal metal interconnect.
Gain
LD
= 1kΩ. For gains ≥5, its bandwidth can be predicted by
×
F
BW
between 500Ω to 1kΩ.
=
200MHz
F
and R
S
+ - 0.5V.
G
S
+ pin. Letting the EN pin float or
can then be chosen to make up
G
9
appear in parallel with the
S
+ and 120µA for I
F
= 0 is optimum.
S
+ will enable
F
also has a
(EQ. 2)
S
-
EL5177
Power Dissipation
With the high output drive capability of the EL5177, it is
possible to exceed the +135°C absolute maximum junction
temperature under certain load current conditions.
Therefore, it is important to calculate the maximum junction
temperature for the application to determine if the load
conditions or package types need to be modified for the
amplifier to remain in the safe operating area.
The maximum power dissipation allowed in a package is
determined according to Equation 3:
Where:
The maximum power dissipation actually produced by an IC
is the total quiescent supply current times the total power
supply voltage, plus the power in the IC due to the load, or:
Where:
By setting the two PD
can solve the output current and R
overheat.
Power Supply Bypassing and Printed Circuit
Board Layout
As with any high frequency device, a good printed circuit
board layout is necessary for optimum performance. Lead
lengths should be as short as possible. The power supply
pin must be well bypassed to reduce the risk of oscillation.
For normal single supply operation, where the V
connected to the ground plane, a single 4.7µF tantalum
capacitor in parallel with a 0.1µF ceramic capacitor from V
to GND will suffice. This same capacitor combination should
be placed at each supply pin to ground if split supplies are to
be used. In this case, the V
supply rail.
For good AC performance, parasitic capacitance should be
kept to a minimum. Use of wire-wound resistors should be
avoided because of their additional series inductance. Use
PD
PD
T
T
θ
V
I
ΔV
application
R
I
SMAX
LOAD
MAX
JA
AMAX
JMAX
S
LD
=
O
= Total supply voltage
= Thermal resistance of the package
V
= Differential load resistance
= Maximum differential output voltage of the
S
=
= Load current
= Maximum quiescent supply current per channel
×
= Maximum junction temperature
= Maximum ambient temperature
T
-------------------------------------------- -
I
SMAX
JMAX
Θ
+
JA
T
V
AMAX
S
MAX
×
ΔV
----------- -
R
LD
equations equal to each other, we
O
S
- pin becomes the negative
LD
to avoid the device
September 14, 2010
S
- pin is
(EQ. 3)
(EQ. 4)
FN7344.5
S
+

Related parts for EL5177IY