EL5123CY Intersil, EL5123CY Datasheet - Page 13
![IC BUFFER QUAD R-R 12MHZ 10-MSOP](/photos/6/58/65824/20-10-msop_sml.jpg)
EL5123CY
Manufacturer Part Number
EL5123CY
Description
IC BUFFER QUAD R-R 12MHZ 10-MSOP
Manufacturer
Intersil
Datasheet
1.EL5423CLZ.pdf
(17 pages)
Specifications of EL5123CY
Amplifier Type
Buffer
Number Of Circuits
4
Output Type
Rail-to-Rail
Slew Rate
18 V/µs
-3db Bandwidth
12MHz
Current - Input Bias
2nA
Voltage - Input Offset
500µV
Current - Supply
2.4mA
Current - Output / Channel
200mA
Voltage - Supply, Single/dual (±)
4.5 V ~ 16.5 V, ±2.25 V ~ 8.25 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
10-MSOP, Micro10™, 10-uMAX, 10-uSOP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Gain Bandwidth Product
-
when sourcing, and
P
when sinking.
where:
If we set the Equations 2 and 3 equal to each other, we can
solve for R
power dissipation curves provide a convenient way to see if
the device will overheat. The maximum safe power
dissipation can be found graphically, based on the package
type and the ambient temperature. By using the previous
equation, it is a simple matter to see if P
device's power derating curves.
Unused Buffers
It is recommended that any unused buffer have the input tied
to the ground plane.
Driving Capacitive Loads
The EL5123, EL5223, EL5323, and EL5423 can drive a wide
range of capacitive loads. As load capacitance increases,
however, the -3dB bandwidth of the device will decrease and
the peaking increase. The buffers drive 10pF loads in
parallel with 10kΩ with just 1.5dB of peaking, and 100pF
with 6.4dB of peaking. If less peaking is desired in these
applications, a small series resistor (usually between 5Ω and
50Ω) can be placed in series with the output. However, this
will obviously reduce the gain slightly. Another method of
reducing peaking is to add a “snubber” circuit at the output.
A snubber is a shunt load consisting of a resistor in series
with a capacitor. Values of 150Ω and 10nF are typical. The
advantage of a snubber is that it does not draw any DC load
current or reduce the gain.
DMAX
i = 1 to Total number of buffers
V
I
V
I
SMAX
LOAD
S
OUT
= Total supply voltage
=
i = Maximum output voltage of the application
i = Load current
= Maximum quiescent current per channel
Σi V
LOAD
[
S
×
i to avoid device overheat. The package
I
SMAX
+
(
V
OUT
13
i V
–
S
- )
×
DMAX
EL5123, EL5223, EL5323, EL5423
I
LOAD
exceeds the
i
]
(EQ. 3)
Power Supply Bypassing and Printed Circuit
Board Layout
As with any high frequency device, good printed circuit
board layout is necessary for optimum performance. Ground
plane construction is highly recommended, lead lengths
should be as short as possible, and the power supply pins
must be well bypassed to reduce the risk of oscillation. For
normal single supply operation, where the V
connected to ground, a 0.1µF ceramic capacitor should be
placed from V
should then be connected from V
4.7µF capacitor may be used for multiple devices. This same
capacitor combination should be placed at each supply pin
to ground if split supplies are to be used.
S
+ pin to ground. A 4.7µF tantalum capacitor
S
+ pin to ground. One
S
- pin is
August 31, 2010
FN7176.3