SE5230DR2G ON Semiconductor, SE5230DR2G Datasheet
SE5230DR2G
Specifications of SE5230DR2G
Available stocks
Related parts for SE5230DR2G
SE5230DR2G Summary of contents
Page 1
NE5230, SA5230, SE5230 Low Voltage Operational Amplifier The NE5230 is a very low voltage operational amplifier that can perform with a voltage supply as low as 1 high addition, split or single supplies ...
Page 2
MAXIMUM RATINGS Rating Single Supply Voltage Dual Supply Voltage Input Voltage (Note 1) Differential Input Voltage (Note 1) Common−Mode Voltage (Positive) Common−Mode Voltage (Negative) Power Dissipation (Note 2) Thermal Resistance, Junction−to−Ambient Operating Junction Temperature (Note 2) Operating Temperature Range 80 ...
Page 3
DC AND AC ELECTRICAL CHARACTERISTIC kW, full input common−mode range, over full operating temperature range. L Characteristic Symbol NE5230, SA5230 Offset Voltage V OS Drift V OS Offset Current I OS Drift I OS Bias Current I ...
Page 4
DC AND AC ELECTRICAL CHARACTERISTIC kW, full input common−mode range, over full operating temperature range. L Characteristic Symbol SE5230 Offset Voltage V OS Drift V OS Offset Current I OS Drift I OS Bias Current I B ...
Page 5
DC AND AC ELECTRICAL CHARACTERISTIC kW, full input common−mode range, over full operating temperature range. L Characteristic Symbol NE5230, SA5230, SE5230 Large−Signal Open−Loop Gain A VOL Output Voltage Swing V OUT Slew Rate SR Inverting Unity Gain ...
Page 6
Input Stage Operational amplifiers which are able to function at minimum supply voltages should have input and output stage swings capable of reaching both supply voltages within a few millivolts in order to achieve ease of quiescent biasing and to ...
Page 7
Output Stage Processing output voltage swings that nominally reach to less than 100 mV of either supply voltage can only be achieved by a pair of complementary common−emitter connected transistors. Normally, such a configuration causes complex feed−forward signal paths that ...
Page 8
... THERMAL CONSIDERATIONS When using the NE5230, the internal power dissipation capabilities of each package should be considered. ON Semiconductor does not recommend operation at die temperatures above 110°C in the SO package because of its inherently smaller package mass. Die temperatures of 150°C can be tolerated in all the other packages. With this ...
Page 9
The full output power bandwidth range for V 2 above 40 kHz for the maximum bias current setting and greater than 10 kHz at the minimum bias current setting. If extremely low signal distortion (<0.05%) is required at ...
Page 10
REMOTE TRANSDUCER WITH CURRENT TRANSMISSION There are many ways to transmit information along two wires, but current transmission is the most beneficial when the sensing of remote signals is the aim further enhanced in the form of 4.0 ...
Page 11
What this means is that several instruments, such as a chart recorder, a meter controller, as well as a long cable, can be connected in series on the loop and still obtain accurate readings if the total resistance ...
Page 12
HALF−WAVE RECTIFIER WITH RAIL−TO−GROUND OUTPUT SWING Since the NE5230 input common−mode range includes both positive and negative supply rails and the output can also swing to either supply, achieving half−wave rectifier functions in either direction becomes a simple task. All ...
Page 13
Biased to Ground Figure 11. Performance Waveforms for the Circuits in Figures 9 and 10. Good response is shown at 1.0 and 10 kHz for both circuits under full swing with a 2.0 V supply. 500 ...
Page 14
By adding another NE5230 in an inverting summer configuration at the output of the half−wave rectifier, a full−wave can be realized. The values for the input and feedback resistors must be chosen so that each peak will have equal amplitudes. ...
Page 15
CONCLUSION The NE5230 is a versatile op amp in its own right. The part was designed to give low voltage and low power operation without the limitations of previously available amplifiers that had a multitude of problems. The previous application ...
Page 16
... Plastic Dual In−Line Package (PDIP−8) SA5230NG 8−Pin Plastic Small Outline (SO−8) Package SE5230DG 8−Pin Plastic Small Outline (SO−8) Package SE5230DR2G †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. MARKING DIAGRAMS S5230 ...
Page 17
NOTE 5 F TOP VIEW e 0.010 SIDE VIEW PACKAGE DIMENSIONS PDIP−8 CASE 626−05 ISSUE M NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME 2. CONTROLLING ...
Page 18
... *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “ ...