X40031S14-BT1 Intersil, X40031S14-BT1 Datasheet - Page 13
![IC VOLTAGE MONITOR TRPL 14-SOIC](/photos/5/65/56531/20-14-soic_sml.jpg)
X40031S14-BT1
Manufacturer Part Number
X40031S14-BT1
Description
IC VOLTAGE MONITOR TRPL 14-SOIC
Manufacturer
Intersil
Type
Multi-Voltage Supervisorr
Datasheet
1.X40031S14Z-A.pdf
(23 pages)
Specifications of X40031S14-BT1
Number Of Voltages Monitored
3
Output
Open Drain or Open Collector
Reset
Active Low
Reset Timeout
Adjustable/Selectable
Voltage - Threshold
1.8V, 2.6V, 4.4V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
14-SOIC (3.9mm Width), 14-SOL
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
In the read mode, the device will transmit 8-bits of data,
release the SDA line, then monitor the line for an
acknowledge. If an acknowledge is detected and no stop
condition is generated by the master, the device will continue
to transmit data. The device will terminate further data
transmissions if an acknowledge is not detected. The master
must then issue a stop condition to return the device to
Standby mode and place the device into a known state.
Serial Write Operations
Byte Write
For a write operation, the device requires the Slave Address
Byte and a Word Address Byte. This gives the master access
to any one of the words in the array. After receipt of the Word
Address Byte, the device responds with an acknowledge, and
awaits the next eight bits of data. After receiving the 8 bits of
the Data Byte, the device again responds with an
acknowledge. The master then terminates the transfer by
generating a stop condition, at which time the device begins
the internal write cycle to the nonvolatile memory. During this
internal write cycle, the device inputs are disabled, so the
device will not respond to any requests from the master. The
SDA output is at high impedance. See Figure 10.
A write to a protected block of memory will suppress the
acknowledge bit.
Stops and Write Modes
Stop conditions that terminate write operations must be sent
by the master after sending at least 1 full data byte plus the
subsequent ACK signal. If a stop is issued in the middle of a
data byte, or before 1 full data byte plus its associated ACK
is sent, then the device will reset itself without performing the
write. The contents of the array will not be effected.
Acknowledge Polling
used to take advantage of the typical 5ms write cycle time.
Once the stop condition is issued to indicate the end of the
master’s byte load operation, the device initiates the internal
high voltage cycle. Acknowledge polling can be initiated
immediately. To do this, the master issues a start condition
followed by the Slave Address Byte for a write or read
The disabling of the inputs during high voltage cycles can be
DATA OUTPUT FROM
FROM RECEIVER
TRANSMITTER
DATA OUTPUT
SCL FROM
MASTER
13
START
FIGURE 9. ACKNOWLEDGE RESPONSE FROM RECEIVER
X40030, X40031, X40034, X40035
1
operation. If the device is still busy with the high voltage
cycle then no ACK will be returned. If the device has
completed the write operation, an ACK will be returned and
the host can then proceed with the read or write operation.
See Figure 10.
Serial Read Operations
Read operations are initiated in the same manner as write
operations with the exception that the R/W bit of the Slave
Address Byte is set to one. There are three basic read
operations: Current Address Reads, Random Reads, and
Sequential Reads.
FIGURE 10. ACKNOWLEDGE POLLING SEQUENCE
COMMAND SEQUENCE?
COMPLETE. CONTINUE
COMMAND SEQUENCE
HIGH VOLTAGE CYCLE
ENTER ACK POLLING
CONTINUE NORMAL
(READ OR WRITE)
READ OR WRITE
ADDRESS BYTE
COMPLETED BY
ISSUING STOP.
ISSUE START
I
RETURNED?
8
SSUE SLAVE
BYTE LOAD
PROCEED
ACK
YES
YES
ACKNOWLEDGE
9
NO
NO
ISSUE STOP
ISSUE STOP
August 25, 2008
FN8114.2