X40415V8I-BT1 Intersil, X40415V8I-BT1 Datasheet - Page 7
![no-image](/images/manufacturer_photos/0/3/341/intersil_sml.jpg)
X40415V8I-BT1
Manufacturer Part Number
X40415V8I-BT1
Description
IC VOLTAGE MON DUAL W/SUP 8TSSOP
Manufacturer
Intersil
Type
Multi-Voltage Supervisorr
Datasheet
1.X40415V8IZ-B.pdf
(24 pages)
Specifications of X40415V8I-BT1
Number Of Voltages Monitored
2
Output
Open Drain or Open Collector
Reset
Active High
Reset Timeout
Adjustable/Selectable
Voltage - Threshold
1.3V, 2.6V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
8-TSSOP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
BP: Block Protect Bit (Nonvolatile)
The Block Protect Bit, BP, determines which blocks of
the array are write protected. A write to a protected
block of memory is ignored. The block protect bits will
prevent write operations to half or none of the array.
PUP1, PUP0: Power-up Bits (Nonvolatile)
The Power-up bits, PUP1 and PUP0, determine the
t
shown in the following table.
WD1, WD0: Watchdog Timer Bits (Nonvolatile)
The bits WD1 and WD0 control the period of the
Watchdog Timer. The options are shown below.
Writing to the Control Registers
Changing any of the nonvolatile bits of the control and
trickle registers requires the following steps:
– Write a 02H to the Control Register to set the Write
– Write a 06H to the Control Register to set the
PURST
BP
PUP1
WD1
0
1
Enable Latch (WEL). This is a volatile operation, so
there is no delay after the write. (Operation pre-
ceded by a start and ended with a stop).
Register Write Enable Latch (RWEL) and the WEL
bit. This is also a volatile cycle. The zeros in the data
byte are required. (Operation proceeded by a start
and ended with a stop).
0
0
1
1
0
0
1
1
time delay. The nominal power-up times are
100h – 1FFh (256 bytes)
Protected Addresses
PUP0
WD0
0
1
0
1
0
1
0
1
(Size)
None
Power-on Reset Delay (
Watchdog Time Out Period
disabled (factory setting)
200ms (factory setting)
7
200 milliseconds
25 milliseconds
1.4 seconds
400ms
800ms
50ms
X40410, X40411, X40414, X40415
Memory Array
Upper Half of
Array Lock
None
t
PURST
)
– Write a one byte value to the Control Register that
– A read operation occurring between any of the
– The RWEL bit cannot be reset without writing to the
To illustrate, a sequence of writes to the device con-
sisting of [02H, 06H, 02H] will reset all of the nonvola-
tile bits in the Control Register to 0. A sequence of
[02H, 06H, 06H] will leave the nonvolatile bits
unchanged and the RWEL bit remains set.
FAULT DETECTION REGISTER
The Fault Detection Register (FDR) provides the user
the status of what causes the system reset active. The
Manual Reset Fail, Watchdog Timer Fail and three
Low Voltage Fail bits are volatile.
The FDR is accessed with a special preamble in the
slave byte (1011) and is located at address 0FFh. It
can only be modified by performing a byte write
operation directly to the address of the register and
only one data byte is allowed for each register write
operation.
There is no need to set the WEL or RWEL in the
control register to access this fault detection register.
LV1F
has all the control bits set to the desired state. The
Control register can be represented as qxys 001r in
binary, where xy are the WD bits, s isthe BP bit and
qr are the power-up bits. This operation proceeded
by a start and ended with a stop bit. Since this is a
nonvolatile write cycle it will take up to 10ms to
complete. The RWEL bit is reset by this cycle and
the sequence must be repeated to change the non-
volatile bits again. If bit 2 is set to ‘1’ in this third step
(qxys 011r) then the RWEL bit is set, but the WD1,
WD0, PUP1, PUP0, and BP bits remain unchanged.
Writing a second byte to the control register is not
allowed. Doing so aborts the write operation and
returns a NACK.
previous operations will not interrupt the register
write operation.
nonvolatile control bits in the control register, power
cycling the device or attempting a write to a write
protected block.
7
LV2F
6
5
0
WDF
4
3
0
2
0
March 28, 2005
1
0
FN8116.0
0
0