MIC5258-1.2YM5 TR Micrel Inc, MIC5258-1.2YM5 TR Datasheet
MIC5258-1.2YM5 TR
Specifications of MIC5258-1.2YM5 TR
MIC5258-1.2YM5 TR
MIC5258-1.2YM5TR
MIC5258-1.2YM5TR
Related parts for MIC5258-1.2YM5 TR
MIC5258-1.2YM5 TR Summary of contents
Page 1
... MIC5258 General Description The MIC5258 is an efficient, precise CMOS voltage regula- tor with power good output. The MIC5258 offers better than 3% initial accuracy, and constant ground current (typically 100µA)over load . The MIC5258 also works with low-ESR ceramic capacitors, reducing the amount of board space necessary for power applications, critical in hand-held wireless devices ...
Page 2
... Pin Description Pin Number Pin Name GND OUT MIC5258 EN GND LNxx KNxx OUT MIC5258-x.xBM5/YM5 Pin Function Supply Input Ground Enable/Shutdown (Input): CMOS compatible input. Logic high = enable; logic low = shutdown. Do not leave open. Power Good Output Regulator Output 2 Micrel, Inc. April 2006 ...
Page 3
... J Min Typical –3 –4 –0.3 3.5 0.45 110 110 = 150mA tbd OUT 160 350 1.6 0.01 0.01 150 10 89 0.02 0.01 1 Micrel, Inc Max Units 0.3 %/ µA 150 µA 150 µ 0 µA µA °C ° 0.1 V µ MIC5258 ...
Page 4
... IN EN Reference Voltage Thermal Sensor Under- voltage Lockout Overcurrent Dropout Detection Timing Diagram V 97% OUT V EN Min - Max 1-5ms V PG MIC5258 Startup/ Quickstart Shutdown Control FAULT Error Current Amplifier Amplifier ACTIVE SHUTDOWN Out of Regulation Detection Delay 4 PULL UP OUT PULL DOWN PG GND ...
Page 5
... I = 150mA 1.175 OUT 1.170 2.6 3.1 3.6 4.1 4.6 5.1 5.6 6.1 INPUT VOLTAGE (V) Enable Voltage vs. Input Voltage 1.4 1.3 1.2 1.1 1.0 0.9 0.8 0 100µA OUT 0.6 2.6 3.1 3.6 4.1 4.6 5.1 5.6 6.1 INPUT VOLTAGE (V) MIC5258 ...
Page 6
... MIC5258 MIC5258 Enable Voltage vs. Temperature 1. 3.3V IN 1.15 1.10 1.05 1.00 0.95 0.90 0.85 0.80 -40 - 100120140 TEMPERATURE (°C) Power Good Characteristic TIME (250µs/div) 6 Micrel, Inc. April 2006 ...
Page 7
... MIC5258 Applications Information Enable/Shutdown The MIC5258 comes with an active-high enable pin that al- lows the regulator to be disabled. Forcing the enable pin low disables the regulator and sends it into a “zero” off-mode-cur- rent state. In this state, current consumed by the regulator goes nearly to zero. Forcing the enable pin high enables the output voltage. This part is CMOS and the enable pin cannot be left fl ...
Page 8
... Regulator Thermals section of Micrel’s Designing with Low-Dropout Voltage Regulators handbook. Dual-Supply Operation When used in dual supply systems where the regulator load is returned to a negative supply, the output voltage must be diode clamped to ground. MIC5258 8 Micrel, Inc. April 2006 ...
Page 9
... Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify April 2006 SOT-23-5 ( (408) 474-1000 FAX WEB Micrel for any damages resulting from such use or sale. © 2001 Micrel Incorporated 9 http://www.micrel.com Micrel, Inc. MIC5258 ...