LT1529IQ-5#TRPBF Linear Technology, LT1529IQ-5#TRPBF Datasheet - Page 9

IC LDO W/SHTDWN 5V 3A DDPAK-5

LT1529IQ-5#TRPBF

Manufacturer Part Number
LT1529IQ-5#TRPBF
Description
IC LDO W/SHTDWN 5V 3A DDPAK-5
Manufacturer
Linear Technology
Datasheet

Specifications of LT1529IQ-5#TRPBF

Regulator Topology
Positive Fixed
Voltage - Output
5V
Voltage - Input
Up to 15V
Voltage - Dropout (typical)
0.6V @ 3A
Number Of Regulators
1
Current - Output
3A
Current - Limit (min)
3.2A
Operating Temperature
-45°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
TO-263-5, D²Pak (5 leads + Tab), TO-263BA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LT1529IQ-5#TRPBFLT1529IQ-5
Manufacturer:
LT
Quantity:
9 538
Company:
Part Number:
LT1529IQ-5#TRPBFLT1529IQ-5#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LT1529IQ-5#TRPBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Thermal Considerations
The power handling capability of the device will be limited
by the maximum rated junction temperature (125°C). The
power dissipated by the device will be made up of two
components:
1. Output current multiplied by the input/output voltage
2. Ground pin current multiplied by the input voltage:
The GND pin current can be found by examining the GND
Pin Current curves in the Typical Performance Character-
istics. Power dissipation will be equal to the sum of the two
components listed above.
The LT1529 series regulators have internal thermal limit-
ing designed to protect the device during overload condi-
tions. For continuous normal load conditions the maxi-
mum junction temperature rating of 125°C must not be
exceeded. It is important to give careful consideration to
all sources of thermal resistance from junction to ambient.
Additional heat sources mounted nearby must also be
considered.
For surface mount devices heat sinking is accomplished
by using the heat spreading capabilities of the PC board
and its copper traces. Experiments have shown that the
heat spreading copper layer does not need to be electri-
cally connected to the tab of the device. The PC material
can be very effective at transmitting heat between the pad
area, attached to the tab of the device, and a ground or
power plane layer either inside or on the opposite side of
the board. Although the actual thermal resistance of the PC
material is high, the length/area ratio of the thermal
resistor between layers is small. Copper board stiffeners
and plated through-holes can also be used to spread the
heat generated by power devices.
The following tables list thermal resistances for each
package. For the TO-220 package, thermal resistance is
given for junction-to-case only since this package is
usually mounted to a heat sink. Measured values of
thermal resistance for several different copper areas are
listed for the DD package. All measurements were taken in
still air on 3/32" FR-4 board with 1-oz copper. This data can
be used as a rough guideline in estimating thermal resis-
A
PPLICATI
differential: I
I
GND
• V
IN
.
OUT
O
U
• (V
S
IN
I FOR ATIO
U
– V
OUT
), and
W
U
Table 1. Q Package, 5-Lead DD
TOPSIDE*
2500 sq. mm 2500 sq. mm 2500 sq. mm
1000 sq. mm 2500 sq. mm 2500 sq. mm
125 sq. mm
* Device is mounted on topside.
T Package, 5-Lead TO-220
Thermal Resistance (Junction-to-Case) = 2.5°C/W
Calculating Junction Temperature
Example: Given an output voltage of 3.3V, an input voltage
range of 4.5V to 5.5V, an output current range of 0mA to
500mA, and a maximum ambient temperature of 50°C,
what will the maximum junction temperature be?
The power dissipated by the device will be equal to:
where, I
so,
If we use a DD package, then the thermal resistance will be
in the range of 23°C/W to 33°C/W depending on copper
area. So the junction temperature rise above ambient will
be approximately equal to:
The maximum junction temperature will then be equal to
the maximum junction temperature rise above ambient
plus the maximum ambient temperature or:
Output Capacitance and Transient Performance
The LT1529 is designed to be stable with a wide range of
output capacitors. The minimum recommended value is
22µF with an ESR of 0.2Ω or less. The LT1529 is a
tance. The thermal resistance for each application will be
affected by thermal interactions with other components as
well as board size and shape. Some experimentation will
be necessary to determine the actual value.
COPPER AREA
I
V
I
P = 500mA • (5.5V – 3.3V) + (3.6mA • 5.5V)
1.12W • 28°C/W = 31.4°C
T
OUT(MAX)
OUT(MAX)
GND
JMAX
IN(MAX)
= 1.12W
2500 sq. mm 2500 sq. mm
BACKSIDE
at (I
= 50°C + 31.4°C = 81.4°C
= 5.5V
OUT
• (V
= 500mA
LT1529-3.3/LT1529-5
= 500mA, V
IN(MAX)
BOARD AREA
– V
OUT
IN
= 5.5V) = 3.6mA
(JUNCTION-TO-AMBIENT)
) + (I
THERMAL RESISTANCE
GND
23°C/W
25°C/W
33°C/W
LT1529
• V
IN(MAX)
152935fb
9
)

Related parts for LT1529IQ-5#TRPBF