ATAB-STK-F Atmel, ATAB-STK-F Datasheet
ATAB-STK-F
Specifications of ATAB-STK-F
Related parts for ATAB-STK-F
ATAB-STK-F Summary of contents
Page 1
... Atmel’s UHF FSK/ASK remote control transmitters and receivers combined ® with AVR Flash microcontrollers. The RF Design Kit consists of the Flamingo interface board ATAB-STK receiver (receiver design board transmitter (transmitter design board), and various other components as listed in face board has to be mounted on the AVR Starter Kit STK500 (has to be ordered separately), and forms the hardware connection between Atmel’ ...
Page 2
... The various kit versions and the corresponding board order numbers can be found in the selec- tion guide at http://www.atmel.com/products/Auto/. 4.1 Flamingo Interface Board ATAB-STK-F • Flamingo interface board ATAB-STK-F • AVR microcontroller for STK500 • 8-MHz crystal for STK500 • Atmel CD-ROM with software and documentation • ...
Page 3
Figure 4-1. 4886B–RKE–01/06 Hardware Description Flamingo Kit Contents 3 ...
Page 4
Configuration of STK500 To work with the RF Design Kit, the included and fully programmed AVR microcontroller has to be plugged into the DIL socket SCKT3100A3, and the 8-MHz quartz crystal into the socket CRYSTAL. Additionally, the connections need ...
Page 5
... Figure 6-1. 6.2 Application Board Interfaces (X1, X2, J37) When using devices of the ATAB5xxx/ATAB862xx series, there are usually two modules involved: a receiver and a transmitter. The receiver is plugged into sockets X1 and X2 mounted on the Flamingo. An enlarged picture is shown in the right half of The transmitter is configured by the STK500 microcontroller. Therefore, it must be plugged into the socket J37, mounted in the area enlarged in the left part of tion against short circuits, socket J37 is fitted with a polarizing key between pin 3 and pin 4 ...
Page 6
Figure 6-2. 6.3 Voltage Regulation Block There are two voltage regulators in the voltage regulation block for future use and for RF mod- ules with supply voltages other than 5V. For the RF Design Kit, both voltage regulators are not ...
Page 7
User Interface Block In this area of the Flamingo, the user interface devices are mounted. To control the LCD and the joystick, an ATmega16 is used. The joystick provides a flexible way of dealing with user input and making ...
Page 8
... Figure 6-5. Menu Structure Atmel Germany GmbH Automotive & Control Hardware Description Flamingo 8 User Settings Load Settings from... Transmitter Button 1 Button 2 Button 3 Receiver Evaluation Sensitivity Receiving Mode Off Command Configuration 1 Configuration 2 Configuration 3 Configuration 4 Continuous Telegram Single Telegram Continuous Pattern Single Pattern ...
Page 9
Operation of the RF Design Kit 7.1 Assembly of the Kit’s Components To configure the RF transmitter or receiver, the appropriate design board must be connected to the Flamingo age, the design boards must be plugged in as shown ...
Page 10
Starting the RF Design Kit 7.2.1 Connecting the RF Design Kit To ensure proper operation, the following steps should be carried out before starting the RF Design Kit software: 1. Insert the lithium cell into the battery holder of ...
Page 11
The 64 samples will be examined in the microcontroller to distinguish between a valid signal from a corresponding transmitter and signals due to noise. This is done by a time frame check where the samples are continuously compared to a ...
Page 12
Flamingo Board Schematics Figure 8-1. Main Unit Schematic (Expand 0) MAX3002 PC7_S U_Low 5V IC8G5 MAX3002 PA3_S U_Low 5V IC8G2 MAX3002 PA1_S U_Low 5V IC8G1 Hardware Description Flamingo 12 Expand 0 MA20-2 GND GND 1 2 AUXI0 3 ...
Page 13
Figure 8-2. Main Unit Schematic (Expand 1) MAX3002 U_Low PB7_S 5V MAX3002 IC6G1 PB5_S U_Low 5V MAX3002 IC6G3 PB1_S 5V MAX3002 IC7G1 PD7_S U_Low 5V MAX3002 IC7G2 PD5_S 5V MAX3002 IC7G4 PD3_S U_Low 5V MAX3002 IC7G5 PD1_S 5V IC7G7 4886B–RKE–01/06 ...
Page 14
Figure 8-3. Power Supply Schematic VTG VTG (rechangable battery or STK) VS (power supply) V Figure 8-4. Level Shifter Schematic + 5V V_RF VCC V_L 19 2 C35 C36 IC8G10 Hardware Description Flamingo 14 D14 ...
Page 15
Figure 8-5. User Interface Schematic red green D6 D7 J23 S2 R49 + J22 R48 + R64 + MHz UI-Reset R26 R26 ...
Page 16
Figure 8-6. Connectors for RF Transmitter, Receiver and Transceiver Chipsets Hardware Description Flamingo 16 Receiver X2 PE0_RXTX J8 ICP PE0 Transmitter BU08-2 B1 R10 30 k PA3 R8 PA2 R7 PA1 PA0 1 k ...
Page 17
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...